Discussion Locked

VPN over the internet

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have been trying to get a VPN connection to work over the Internet with out any success. I have read the setup instruction as outlined by Microsoft and other sources that I have run across but I am still having problems. When I try to connect to the VPN server I get the response that ?The computer that you are dialing in to does not respond to a network request and to check your server type setting.? I am using NetBEUI for the VPN connection and during the connection process the VPN connectoron the server starts to initialize but the connection is never complete. The connection works when connection from a system on the local network.
Can some one help me with problem? Have I over looked something?

13 replies

by gray.strickland

So that people can better help you, please post the following information: (1) OS of the vpn client, (2) OS of the vpn server, if a pc, (3) make and model of vpn server, if a hardware vpn server, such as a Netopia router, (4) verify what protocol(s)you are trying to use on the vpn client, (5) verify what protocol(s) you have available on your vpn server.

I had a heckuva time myself troubleshooting a vpn connection on my system and so I know that the above will be helpful in finding the problem.

by arg cio

might not work.. many people don't allow it through their internet routers, TCP/IP only (unless it is NetBIOS over TCP). Even so, I suggest using ONLY TCP/IP (and allow NetBIOS over TCP). The reason it starts to initialize is your sending both TCP and Netbeui to the router to initiate a connection, and the TCP hits it. but then your VPN software tries to talk Netbeui, and that doesn't get past the first router. good luck, and let me know if this helped.

by arg cio

thanks for laughing.. we all need a good laugh. but I didn't mean to suggest he use it, I meant use TCP/IP, and if you must, try netBIOS.

by gherkin

Netbeui is not routable. Even though the VPN tunnel is established via TCP, I think you're going to have issues when it hits the router.

by arg cio

You're right, netbeui not routable, that's what I meant. but I didn't mean to suggest he use it, I meant use TCP/IP, and if you must, try netBIOS over TCP/IP.

by echalabi

Dear Charlie,

If your VPN works from within the network but not from remote, I would check the Firewall...

by alvin088

VPN is built on TCP/IP. u need to use TCP/IP.
why not try TCP/IP as your router most properly rejected such packets. Besides u're using the internet, use TCP/IP if possible.

by john dickey

Charlie,
We use VPN all the time at our company to allow remote users access. Almost every time we have had a problem setting up, it has been on the client end.

1. Use TCP/IP protocol only
2. If NT server is the host...
Make sure that Log on to network, Use software compression, and Require Encrypted Password, and TCP/IP are the checked items on the server tab of the client setup.

On the TCP/IP Settings Tab of the client...
We block a range of permanent addresses for our clients and they are in the internal address range 192.168.100.xxx. If you are using DHCP to provide dynamic addresses and it is hosted on the dial-in computer you may not have to do this and may choose to use Server assigned IP.

For DNS entries...
We leave the primary and secondary at
0.0.0.0
and set the Wins entry to the 192.168.100.xxx address of our Wins Server

We use IP header compression and uncheck the use default gateway at the bottom of the tab.

This setup works for us every time withoutfail.

One thing to check, look at the VPN adapter and make sure that TCP/IP is binding to it. If it is not, the easiest way to get it to do so is to entirely yank out networking on the client and reinstall from scratch.

On the server end, makesure that the user has dial-in permissions set. User manager is the place to go for this.

Hope this helps,
John Dickey - Head of Information Services
Technomic Publishing
jd@techpub.com

by arg cio

wow, that's a great tutorial in 1930 characters or less!! great job!! But, I think the main problem is item #1. He said he was using Netbeui, and he needs to use TCP/IP! correct me if I'm wrong, I don't think I am. Would love to hear the solution.

by john dickey

No, you are absolutely right...NetBeui just dosen't cut the mustard across the Inet.

I tend to talk and write too much, but I wanted to supply an answer that could solve the problem for Charlie.

John Dickey

by wasislos

Of course you guys can laugh. You don't know that netbeui works. But, can you fix the IP problem, that is the question. Does anyone know why TCP/IP would not work over VPN with DHCP and WINS on, MSCHAP and domain entered. Yes......IP is bound tothe adapter of the client, and I read John's article.
Any suggs?

This discussion is closed to new replies.