Discussion Locked

W2K RAS errors 619 771 721 Juno ISP

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
I have a Dell PC running W2K. The PC has an external modem Zoom/Modem USB v.92 Model 3090. It will connect to a test account that I create with dial up networking using just the phone number to access. I do not use software for the test account. When I use Juno I recieve the RAS errors 771 and 721. I uninstalled the advanced networking components, TCP/IP and the Winsock folders. Uninstalled Juno as well. When I reinstalled the networking components and reinstalled Juno it dialed out to Juno's server and downloaded the local access numbers for me to choose and accepted the user name and PW. When I try to log on after the initial setup, that is whn I get the RAS errors.

12 replies

by pocono

Hi! HOpe this helps....

Error 771: 1. Make sure the user is dialing the correct phone number. Make sure the phone number they are dialing is not having issues.

2. Check the connectoid and Network settings.

3. Make sure modem is setup properly, try inits, check for updated drivers.

4. Lower the Fifo buffers. Lower port speed to 57600, making sure the checkbox to 'only connect at this speed' is unchecked.

5. Check into line noise.

Error 619: 1. Reboot.

2. Make sure that no other programs are using your modem. Fax software, Supervoice, etc...

Error 621:
1. Reboot the machine, verify your Username and Password, and try again. Check for realms, if in NT make sure you have nothing under domain, accept any auth including clear text is checked, and try unchecking Enable PPP LCP extensions. Make sure logon to network isn't checked. Make sure that nothing is typed in the DOMAIN field if this is NT.

2. This is often a POP problem. Try logging onto a different POP. 718 is usually on the ISP's end, but NOT ALWAYS. If there are multiple calls coming into the ISP's callcenter then they could see a problem, but if not, it is probably the user's computer.

3. Nuke the pwl files.

4. Have ISP reset the password.

5. Recreate connectoid.

6. Full uninstall and reinstall of connectoid, network, and DUN/RAS.

7. This can sometimes also be a communications problem caused by heavy line noise or modem problems. Try updating the modem drivers, inits, commas, etc...and have a line noise test performed.

by pocono

Sorry-forgot about error 619....

This error message will occur if the RAS server isn't properly added to the Active Directory-you are on a domain, yes??

by casemaker

What would be the best way to reset all the networking and dial up components. You can see from my thread that I have done quit a bit already and it did not work. Any thoughts on clearing all network and dial up and reinstalling

by cg it

I read the first answer. I'll add this from the list of error codes for Dial up & Remote Access

619 = the port is disconnected
721= remote PPP peer is not responding
771= the connection attempt failed because the network was to busy

Now we really do need some clarification here. Is your Dell running W2K Pro. NOT W2K server or any server version thereof and are you trying to connect TO a W2K Remote Access Server via RRAS using a dialup connection into Juno ISP, then VPN into the network?

PPTP L2TP are the 2 VPN miniports setup on a RRAS server [beside direct dial in via a modem]. PPTP comes in through port 1723. Now depending upon how your trying to contact the RRAS server[VPN over the internet or direct dial in] AND if it's VPN over the internet AND there is a router or firewall BEFORE the RRAS server it has to either allow PPTP passthrough or foward PPTP port 1723 traffic to the RRAS server. [Direct Dial is directly in and a firewall/router doesn't affect the call].

If you time out while attempting to contact the RRAS server over VPN I would venture RRAS isn't receiving the message due to closed ports AND/OR a remote access rule is denying the connection attempt.

by cg it

cripes almost forgot PPTP also uses GRE port 47 [PPTP passthrough]

Now if you have a W2K AD network WITH RRAS installed and you have a workstation there. you can setup and test a VPN type connection locally ie simulate a VPN connection in via the LAN. You create a new network connection on the client computer, follow the wizard and choose VPN connection. Load in the proper parameters noting that the IP address for the RRAS server will be a LAN IP then try the connection. IF RRAS is propertly setup including the rules to meet for remote access, you should be able to connect to the RRAS server. If this is sucessful then the problem with external clients connection is NOT the RRAS server or it's configuration but a firewall blocking the traffic into the RRAS server.

by cg it

Now from your description of the problem, it sounds like you are trying to install Juno software on your W2K computer and use Juno as your ISP. After installing Juno and getting access #'s your account and password to use Juno service as your ISP you try to connect TO Juno and receive a RRAS error message. So, HOW are you setting up your dialup connection? Are you creating a VPN Dialup connection into Juno? IF you are you shouldn't. You don't create a dialup VPN connection into Juno. you use the Juno client program which will dialup for you and authenticate you to Juno. If you use your web browser for surfing the web, you specify in the web browser to use the Juno dialup client program to extablish a connection to Juno, then with an active connection, you can use your browser to browse the internet.

by cg it

If your using Juno as your ISP AND your trying to remotely connect to a W2K Network running RRAS via VPN on your computer running W2K Pro and receive the error you stated the problem isn't your end it's the RRAS server end.

by casemaker

this is W2K Pro. I am not trying to do anything extreme. I simply loaded juno, clicked the shortcut and let it dial and I get the RAs. This computer is not on ant kind of network, home or corporate.

by casemaker

*NEW ERROR MESSAGE*
Hi Everyone,
I thought I covered this but I will say it again. All I am doing is loading Juno with the Juno disk, it dials out fine and lets me get the local access numbers. When I click on the shortcut on the desktop is when I get the error messages. After doing a full uninstall of juno including a registry search and of all network components I am familiar with, I uninstall all from network properties as well as all advanced items I downloaded the latest version of Juno installed it and it dialed out to obtain access numbers and was ok getting numbers. It is when i click on the shortcut to connect that I get new error meaasage. The new message is ordinal 313 could not be located in oleaut32.dll

This discussion is closed to new replies.