Discussion Locked

WAN improvements (a casestudy)

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
how can I upgrade or improve a network that will merge voice video and data, to serve a WAN that currently consist of 56kbps leased lines Dail-up modems and multiple T1 lines? Also, 17 additional offices will be added in 12 months.

14 replies

by tbradley

First thing I would do would be upgrade the router at your central hub site and tie all the wan links to it. A Cisco 3640 with ATM would be your best bet. If you really must keep the Dial-ups, add a modem module to the router, which greatly simplifies both equipment and configuration.

Next, standardize your medium to large branch offices by changing over from 56k leased to Fractional T-1 again with cisco routers, 2500 series or so. The Fractionals can be adjusted easily to keep up with yourbandwidth requirements.

Keep your 56k equipment, and preconfigure it for the additonal offices that are coming in.

There's tons of variables in this, a lot depends on the unstated - # of users, applications, file transfers, etc. How much e-mail, host systems etc.

The key is however, get your central site set up with plenty of bandwidth, keeping your existing equipment and t1's online. Start moving sites 1 by 1 to the new router. At this point, you might want to consider keeping yourexisting setup as a backup if downtime is a critical issue.

by Former member

Voice over IP? Video feeds to WAN sites? Not good on a WAN. You'll need a router/switch fabric that supports VoIP and QoS. (Look up these terms at www.cisco.com) If you're seriously thinking about channeling this throughout your WAN, you'll need to look at Multicast switching as well. And AT LEAST a T1 to every site, a 5500 or better mulit-layer switch at the home office..etc

by shanghai sam

I also think ATM will be your best bet for merging VV&D, but I think you have to evaluate bandwidth requirements and let them determine what equipment is installed and where. Be sure to plan for growth!

Our organization has done videoconferencing over ISDN, but found it pretty choppy. We are currently holding VTC's over T-1 links using Sony Team Stations that require 384Kbps. This works much better. As for dial-up, we've used the Cisco 5200 with great success and reliability. I believethey've dropped the 5200 in favor of the 5300 series now.

Without knowing your physical layout, it's hard to make specific recommendations, but you might want to consider "site clustering". By that I mean home the offices within a given city to a specific branch (or possibly equipment co-located at a telco) and then run a higher speed link from there to your main branch. You should save money on circuit costs without an appreciable loss in service. Administration and troubleshooting will also be simpler. You may be able to find a national carrier like Sprint or AT&T to carry ALL your traffic. Their engineers will be able to design and provision all of the interconnects for you. You should also be able to negotiate a very beneficial rate for those circuits. The only caveat for this kind of deal is to plan well enough in advance so any circuit migrations or installations happen when you need them to. Our experience with Sprint (and most of our local carriers) has been to allow at least 4-6 weeks for new circuits.

by ckilday

Freddie,
How big is the network you're dealing with? I mean both in # of sites as well as geographic locations? You might want to consider creating hubs or traffic centers at a primary branch in each city and then create higher speed links between cities and your home office. There's also the possibility of co-locating a router at a city telco rather than homing to an individual branch office. These "hubs" will save you money on local circuit costs and simplify administration and troubleshooting. If the operation is large, contact a national carrier (Sprint/MCI/AT&T) and put the WAN links out to bid. Let their engineers do the grunt design work. Just make sure you do a proper evaluation on your bandwidth needs and plan for growth!This is especially true of the routing/switching equipment you plan to install. The Cisco 3640 recommended earlier is a very versatile choice and has good capacity. It would work very well as a hub router. Cisco has stopped the 2500 series and now uses the 2600 as its business flagship model. Cisco also has its AS5300 series controllers for dial-up. They work well with an ISDN PRI. Finally, if you're going to merge VV&D, I think ATM will likely be your best bet for QOS. Best wishes!

by ckilday

Freddie,
How big is the network you're dealing with? I mean both in # of sites as well as geographic locations? You might want to consider creating hubs or traffic centers at a primary branch in each city and then create higher speed links between cities and your home office. There's also the possibility of co-locating a router at a city telco rather than homing to an individual branch office. These "hubs" will save you money on local circuit costs and simplify administration and troubleshooting. If the operation is large, contact a national carrier (Sprint/MCI/AT&T) and put the WAN links out to bid. Let their engineers do the grunt design work. Just make sure you do a proper evaluation on your bandwidth needs and plan for growth!This is especially true of the routing/switching equipment you plan to install. The Cisco 3640 recommended earlier is a very versatile choice and has good capacity. It would work very well as a hub router. Cisco has stopped the 2500 series and now uses the 2600 as its business flagship model. Cisco also has its AS5300 series controllers for dial-up. They work well with an ISDN PRI. Finally, if you're going to merge VV&D, I think ATM will likely be your best bet for QOS. Best wishes!

by ckilday

Freddie,
Sorry about the multiple entries! I never received confirmation that the first one took...in fact I was asked to login again to Tech Republic so I thought I'd taken too long and had timed out. So I re-wrote it and then when it looked like my system had failed to deliver the message again, I stopped the transfer and submitted the same answer once more. Oops!
- Chris

by ricky

I think atm is right now the most flexible solution. This can be converted over as posible to new equipment Iwould suggest you pick one company and stick with it. You might think about running a tier setup you know run smaller offices to some of the larger offices then the larger ones to the main office but without a lot of questions it will be imposible to give you a complete answer. You might think about useing a dialin server and a pri to replace your dialin lines. you did not say how many you have but with modem to modem you can not get v.90 speeds. with our dialin server just like the isp's use and our own isdn pri we get 48k to 50k all the time.

hope this helps

This discussion is closed to new replies.