Why After BIOS upgrade computer fan makes heavy noises?
After upgrading my computer BIOS its fan stats making heavy noises and expels a lot of air, what could be the problem?? Is there a way to put back the factory BIOS??
Thanks
Windows Forum
After upgrading my computer BIOS its fan stats making heavy noises and expels a lot of air, what could be the problem?? Is there a way to put back the factory BIOS??
Thanks
by dandps Accepted solution
by nepenthe0 Accepted solution
by oh smeg Accepted solution
And what Hardware you have installed. Some Intel BIOS's have the option to allow the CPU to run hotter so the Fans do not run as fast but they are there to Cool the CPU down so running Fast is a good idea.
Some AMD BIOS's have the ability to use the Quite & Cool Option which keeps the fan slower that it would otherwise run while keeping the CPU cool but not as cool as it would like to be. They trade off the CPU temp for noise.
If you have a NB of some description again the BIOS will have a Power Saving Option and this needs to be set in BIOS.
Basically it depends on your Hardware and as you have Updated the BIOS this has removed all prior setting so you need to reset the BIOS.
Col
by nepenthe0 Accepted solution
OH Smeg knows vastly more about this stuff than I do, so I would defer to his recommendations.
Once upon a time, I had a Sony desktop with Windows ME originally installed (yuk). I finally became so exasperated that I performed a clean install of XP Pro. Sony posted an upgraded BIOS for OS 'Migration', along with upgraded drivers for XP Pro.
Among the upgraded drivers was one for the fan control - the fan ran at maximum speed under the new BIOS, whereas the fan normally only did that upon booting.
Upon downloading and installing the fan controller driver upgrade, the fan behaved as before, maximal speed at boot, variable speed depending upon CPU load.
Because this was such an easy fix, I recommended it to 'dandps' - it worked for me. If the problem is any more complicated, I hope you'll help him resolve it.
Rick/Portland, OR
by dandps Accepted solution
by nepenthe0 Accepted solution
OH Smeg's advice is probably correct, although his language may be a bit overtechnical for you.
To view the BIOS (Basic Input/Output System) that you have upgraded, you must hold down a function key during booting. This varies by manufacturer. For Sony, it is the F2 key.
Once you have the BIOS menu, you can navigate that menu using keyboard commands listed in the menu. Look for the fan controller (if listed) and select the appropriate setting. Save 'changes' at exit, and the boot process will continue.
If there is no fan controller in the BIOS menu, I have insufficient expertise to advise you further. Hopefully OH Smeg will monitor your case and help you resolve it (he can fix anything...)
Rick/Portland, OR
by Former member Accepted solution
I will need this so that i can help you out with your problem.
Please post back if you have more problems or questions.
by selltekk Accepted solution
WE have several Gateway PCs that have an issue like this. It is a BIOS issue. I have no clue what the actual cause of it is, but by flashing the BIOS to a different version the problem was corrected.
I banged my head against the wall on this one. Hope you find a solution.
by komokozie Accepted solution
Does this happen even when the system is completely cold, like when Off overnight or for several hours???
It most def, is in the BIOS functions. Mfrs know that there are folks that will/can/dare to upgrade their systems.. including the CPU so they change the BIOS to operate the fan(s) accordingly.
In this situation, with a newer BIOS, they may have made the 'sensing' parameters 'lower' (realizing that even in the past, 'without' a faster/hotter CPU installed, they may feel the CPU should run cooler than their previous 'settings') so that it keeps the fan speed on high for the temp. that your system runs normally.
I myself have never seen a 'fan' driver. It's always been controlled by the BIOS that I know of.
In most newer versions of the BIOS there is a parameter for fan control - i.e. 'Auto/High/Quiet.
!! Now please don't get me wrong !! ...
There def. is s/w out there that can be compatible (or even from your Momboard mfr) to work with the fan(s) through Windows. These actually can work quite nicely.
The cooler that came with the CPU (or, the System itself) is 'most likely' fine for keeping it suffiently cool, albeit noiser always being on high speed.
On another note, and a much 'better' note..
If you want to get past this issue while leaving the 'air-flow' sufficient (or even more than suff'nt) to keep the CPU cooled to 'their' satisfaction, then there are 3rd party CPU coolers (Fan & Heat Sync combos) that are of a very different design and are much more efficient/quieter with even higher cf airflow. You might want to look into that instead. Although it might require a few bucks, this IS the better answer than trying to slow the fan for the sake of volume.
I don't believe 'anyone' who reads this will be able to argue that fact.
PS If you do decide to change the cooler, !! DON'T FORGET !! to use 'Thermal Paste' between the CPU and HeatSync ! ! !
by komokozie Accepted solution
This discussion is closed to new replies.
Sort by Trending