Discussion Locked

why ar ip addresses changing?

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Using internet connection sharing and win98,
the ip addresses on the client machine keep changing. How do I set these ip addresses and keep them from changing? The internet service provider is Road Runner and the host and client are networked using 3com home phone network cards.

7 replies

by joescalia

You are looking for a static ip address. which means your ip address is always the same.
How to do this as follows:
At the Dos promt type in ipconfig and note down your ip address, subnet Mask and gateway address.
After that do the following:
1) right click on network neighborhood and select properties
2)Select the network config tab(should open as default)
3)highlight your nic card select the properites tab
4) select Specify an IP Address button
5) type in your IP Address, Subnet Mask
6) Select the gateway tab and type in the gateway address
7) Select the add button and hit ok all the way thu.
8) Windows will ask you to restart your computer and select Yes.
You should good to go...but check to see if they all took and do the following:
Redo these steps to check to see if they took. Also use the DOS promt to ping the ip and gateway address.
10) AT the c promt type ping and you ip address and gateway for the connection speed.
It sounds like alot but it is not...
GoodLuck

by shanghai sam

Thanks for the help. I went ahead and purchased the 2Wire HomePortal 100 cable/
dsl router and installed it. The isp for this network is RoadRunner. I used the ethernet card in the gateway computer to interface with the 2Wire router and disabledthe HPNA adapter in that computer. I then plugged the 2Wire router into the phone line jack and set up the other computer using the existing HPNA
adapter. Now there is no gateway computer. The network management software
seems like it will make life easier compared to using internet connection sharing and Home Click networking software.

by petemcc

My Roadrunner service gives me a more or less static IP, it?s only changed twice in the last year. Your NIC that is attached to the internet gets it?s address from your ISP?s DHCP server. ICS will assign 192.168.0.1 to your LAN adapter on that host with subnet mask 255.255.255.0 You can assign any address from 192.168.0.2 - 192.168.0.254 to the clients in network TCP/IP properties. This applies only if you are using the Microsoft ICS that is included w/ W98. If you are sharing using the multiple connection option that is available from Roadrunner and have only one NIC on your host machine you may have to live with what they give you (if you set a static IP and Roadrunner assigns a new one you?ll lose connectivity).
Good luck,

by shanghai sam

Thanks. This network is not mine and it became a real pain to maintain (even though Mom would always have lots of cookies for me to munch on). I bought the 2Wire HomePortal 100 and used the nic that the cable modem was hooked to for the interface to the 2Wire router. The router plugged into the phone line and I used the existing HPNA adapter in the other machine. Now there is no host. I think that it will work out well, but time will tell.

by ebob

As mentioned, you are picking up a dynamic IP address. Assuming you are getting this from your Internet provider, you're more or less stuck. You might be able to negotiate with them to get a static IP, as they provide businesses, but be prepared to spend a bit more to make this happen.

Alternatively, you could register with one of the "Dynamic DNS" registires like:

http://www.dyndns.org/

They'll keep track of what IP address you're currently using, and refresh the DNS records accordingly.

by shanghai sam

Thanks. I hope that using the 2Wire HomePortal 100 will make the dynamic ip address transparent to the users of the network like it should be. I never could get this issue straightened out using ics. I like the protection that being behind a hardware firewall will give to the users.

This discussion is closed to new replies.