Question Locked

Why will my fans on my pc kepep on running?

0 helpful
22 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I had this issue before. The fans keep running, the light are on. I did not notice any burn marks. When I pust the button on the monitor, it said to push any key to turn on out of the powersafe mode. Ithink it may be my power supply. I do here it running as well. This happened before and I did several things and it worked again. The computer was turning on and working only when unplugging it. I am running windows vista.

22 replies

by oh smeg

Unplug the Mains Lead the Power Supply is loosing capacitance in the capacitors in it. This means that the Filter Capacitors are failing.

You can use the Antec PS Calculator to work out the size of a replacement Power Supply that you'll require here

http://www.antec.outervision.com/

Col

by zitkat2s

Your informaion is very helpful. I had never replaced a power supply before, but it does not look difficult. It has a dust coating that is thick. I noticed when I took the flashlight to look inside of the PSU. It is a dell computer. The site you gave me is helpful. That computer has had problems since I bought it new from dell. I believe I am doing better on my own in solving the issues. I also want to add another hard drive into the pc. Will that effect the PSU? I am also upgrading to a Nvidia gel force card.

by santeewelding

Take no lip from it. Be careful, also, not to get the Nvidia gel all over everything.

by technocrat25

A computer fan is any fan inside a computer case used for cooling purposes, and may refer to fans that draw cooler air into the case from the outside, expel warm air from inside, or move air across a heatsink to cool a particular component. The use of fans to cool a computer is an example of active cooling.

by older mycroft

He's even got to C&P in order to answer a question about a computer fan cooling system. ;)

by ron k.

My computer pick up dust on the CPU and video card's heatsinks and in the power supply. Every so often I have to take a can of compressed air or CO2 and, with my computers turned off/unplugged, blow the crap off of everything. I've read where you should prevent the power supply fan blades from turning while cleaning as it might generate current. I'm unsure of how true that is but I use a toothpick/pencil whatever to hold them just in case.
Everytime that I've cleaned my computers they quiet back down. You might want to do a sniff test on your power supply too. If they're going bad you may be able to smell them. It's a funky, nose-burning, odor.

by zitkat2s

I cleaned off all my fans and computer. The PSU does not have an oder. I did notice a lot of dust in the PSU. I would have to take it apart to clean it, well at leat open up the housing. I never did that before.

by older mycroft

Not if you intend to remain upon this mortal coil for the foreseeable future.

The danger from residual current inside a computer PSU is nowhere near as dangerous as that within an old CRT monitor, but it'll still give your ticker a bit of a jolt.

Best just blast it with compressed air from the safety of the outside. ;)

by santeewelding

Having gelatinized more of my brain cells over the years than is prudent, have thrown my hands up in surrender to problems of the world, and approach instead with the gentlest humor I can manage, given what I have left.

by zitkat2s

At my age I think some of my brain cells have moved on. :)

by peconet tietokoneet

I take my psu's apart and give them a good clean, but like oldermycroft said, be careful here. It can be done but slowly and with gloves on (not plastic ones). As long as you do not touch anything inside the psu you will be fine.

by oh smeg

Would need to be Electrical Workers Gloves not Dish Washing Gloves as those offer no protection against [b]Electrical Shock.[/b]

But provided that you follow a few steps it's safe enough. The first thing to do is unplug the mains lead and then push the On Button on the front of the computer for at least 30 Seconds. This will discharge the Capacitors inside the PSU.

The problem with opening most Dell PSU is that they are not normal, they have more than just screws holding them together and have clips which need to be slid apart/together as you dismantle/reassemble them. It's really much safer to use Canned Air and stick some insulated item into the Fan to prevent it spinning. ;)

As for adding another HDD you may need to slightly increase the size of the Power Supply to prevent it being overloaded.

PSU come in 2 types there is the Constant Feed Rated ones which will produce their rated power 100% of the time and the Peek Value ones which will produce their Rated Power for a short time under Peek Loadings and then have to drop back to a lower power rating to run all of the time.

This is just like Stereo Equipment the cheap no name makers rate their Power Supplies to a higher value than what they really are to get sales. A good power supply is quite heavy and has a lot of Capacitance built in to protect the insides of the case from all of the junk on the Mains.

Col

by zitkat2s

I do have a pair of electrical gloves. I did notice there are many screws in the PSU. I also noticed the clips. That is why I did not take it apart. I am glad because, I did not know to wear rubber gloves. I waa going to do that before I posted. I did know to press the power button for 30 seconds after I unplugged. Where is a good place to buy a power supply, a hard drive and a graphic card? Also do I have to add another blue wire to the 2nd hard drive. It was already set up for another hard drive, but does not have the blue wire. All the rest is there.

by zitkat2s

I think it may be easier to just buy a new one.

by oh smeg

There are up to 4 Screws that hold the PS into the case. Generally 3 but the number can range from 2 to 4 or it may have a clip inside the case to hold the PS. If there is a clip inside the case it's a special PS that is a odd size and most likely you'll need to modify the case to mount a Standard PS.

As for pulling a PS Apart once it is out of the case there are again up to 4 Screws that hold the cover onto the main part of the PS one may be under a sticker which need to be pealed back to expose the screw. Once you have the screws out it's just a matter of lifting off the cover, though reassembly can be a bit more tricky as some have catches which help hold them together. There are also generally folds in the Cover which drop in under the base to prevent the sides from moving when the PS is assembled. You can easily blow these out with either Compressed Air, Canned Air or a Vacuum Cleaner set on the Blow Side but you need to stop the Fan spinning. It is a DC Motor and if you spin it they generate Electricity which isn't a good thing. ;)

I just stick a small screwdriver into the Fan Opening to stop the blades from spinning but unless you do a lot of Electrical/Electronics work you should use something insulated.

Col

by ron k.

Their normal shipping time has been 2-3 days. Their prices are about the same as NewEgg. I've bought online from them too. I've never had issues with either.
Amazon is pretty cool. I bought a keyboard from them that was DOA and didn't even have to pay the postage to return it. I'll buy from them again.

by oh smeg

But that is because they offer far better protection to the internals of the case which to me is the [b]Important Part[/b] of any Computer and the HDD which is the [b]Expensive Part[/b] if you need to recover the Data off it.

Antec PS's Web Site is here

http://www.antec.com/Believe_it/product.php?Series=MjQ=

With HDD I tend to only use Seagate Drives because of the Warranty on them, and the face that I have very few problems with them other than them getting full too fast of course, but that happens to them all.

http://www.seagate.com/www/en-us/products/desktops/

As for Graphics Cards that depends on what you actually need/want but particularly with non Intel Chip Sets you may run into Compatibility Issues with some NVidia Cards so you'll need to check your M'Board Specs.

As for the second HDD you don't need to add any wires unless you don't have a Power Plug for the Second Drive. If this has a IDE Drive the IDE Data Lead should have a unused Connector on it that allows you to plug in a second but you first need to set a Jumper on the Drive between the Power Plug and the Data Plug. You should set this to either Slave or Cable Select depending on the Data Lead Type. If you have a 40 Wire Data Lead you need to set the drive to Slave and if it is a 80 Wire Cable you can use either Slave or Cable Select CS.

If this is a SATA Drive you'll most likely need a SATA Data Lead but these are not expensive you should be able to get one with the HDD for less than $10.00 easily. Just try to get one with a clip on it to lock it to the M'Board and HDD as it will be less likely to unplug itself.

Col

This discussion is closed to new replies.