Question Locked

why wont my PC detect my keyboard?

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I just built a PC and am trying to boot into bios (I have no operating system and I need to change bios settings for my PC to detect my nvme ssd) but everytime I turn my PC on, the keyboard turns on for about 4 seconds then suts right back off, I have tried clearing CMOS and switching to every other USB port on my motherboard but nothing works, and btw my motherboard doesn't have a ps2 plug, i need a keyboard to work to be able to navigate bios but i cant, ive tried multiple different keyboards in all the usb slots and nothing will work. please help?

5 replies

by kees_b edited

I)t's a good question, but you're the only one who can possibly tell the answer. So only two remarks:
- Any useful information on the screen during a boot with the keyboard connected?
- Take the motherboard out of the case and connect only monitor and keyboard (and graphic card if no onboard graphics). Then boot. If still no luck try another motherboard.

by icy22k

no good information, its the same screen you see on any other pc when u first build it and turn it on, it just shows the bios version, initializing usb controllers, the cpu info, the ram info, and cmos info, but it says theres 1 keyboard and 1 mouse hooked up even even when i have nothing plugged into it

by icy22k

i also tried what u just told me and no luck, i think the chinese motherboard i got was a fake, also i figured out what was causing the short in my pc (half the time when i turn it on it will turn right back off then back on a few times until u stop it) one of my cpu pins that is for powering the cpu is severly bent and is touching 2 other pins, causing the power short and is also probably frying my cpu in the meantime, i already have another cpu coming but ig ill have to buy a name brand motherboard this time like a asus or smth, thanks for your help, i also may switch out the power supply, incase that is also shorting

by oh smeg

Assemble the components on the M;Board attach a Known Good Power Supply and some spare case connectors , sit the M'board the anti-static bag it came in or some clean white paper plug in the power supply and press the power on front panel switch and wait till you either get a beep error code or it just runs.

If it's running attach a video card if it is needed and repeat. If ti starts and stops the Video Card is not comparable with the M'Board & if it runs with no Beep Error Code power down and plug in a monitor and continue again. If it now works plug in a Keyboard and try setting the BIOS from there it is generally the Delete Key you need to press to enter the BIOS Setup but that varies with the different makes of M'Board it may be something different in your case.

As for good M'Boards I find Gigabyte to be the best most reliable and generally great workhorses for my needs but you also need a very good Power Supply. Many of the high Rated ones will provide that power rating for peek loads and then fall back to their basic output which may not be sufficient to run the thing or even worse let spikes through and fry the M'Board, CPU and RAM and everything else connected to it. I use Corsair, Antec or Gigabyte Power Supplies depending on which wholesaler I'm dealing with at the time and while they may not sound great the number on the outside of the case is the normal power rating not their peek load rating and better still if you get something nasty over the mains they will sacrifice themselves and protect everything else inside the case so it's just a matter of New PS and away you go again. Of course that doesn't apply to Lighting Strikes or the like as the voltages are so extreme very little can protect from those things and to be perfectly honest a dead computer will be the least of your problems as everything else will have been destroyed when the lighting Strike hit.

As for as bent pins on CPU's that is mostly because it was not put into the M'Board correctly and was in the wrong orientation the destruction manual of the M'Board should show you which way it goes around and how to insert it. These are all Zero Insertion Force CPU's these days so they should just drop into the socket and no force is needed just make sure you lift the lever or cover before attempting to insert the CPU. Quite often bent pins also mean that the M'Board has been fried as well as the CPU.

by paulrobbins092 edited

If your PC isn't detecting your keyboard, it could be due to hardware or driver issues.

This discussion is closed to new replies.