Discussion Locked

Win 95 Starup

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a Compaq Armada 1530 with a compltely empty hard drive, no driver to CD-ROM, and a Win 95 floppy. But I cannot figure the commands for running this startup floppy. Any tips???

21 replies

by bill cassada

Commands? You need to set the BIOS to boot from the floppy drive. Try holding F10 to get into the BIOS. I think this is the correct key for the Armada.

by ryan

Correct! F10 does access the BIOS. I've got that. I do not know the DOS language enough to load Windows from the floppy.

by ryan

Yes, correct! F10 is the key for accessing the BIOS. I need to know how to use the Win95 floppy to install Windows. When I boot with the diskette, naturally, I get the 'A' prompt. Where to go from here?

by bgriffith

The easiest thing to do is boot from a Win98 startup disk, copy over the Win95 CD to the hard drive, and perform the install locally.

If you don't have a Win98 startup disk, you'll have to find the appropiate drivers for your CD-ROM.

by ryan

A few days ago I booted with Win 98 CD and was able to acces the CD-ROM drive. But since then I have lost access to the CD-ROM drive and cannot remember what I did before. We also downloaded a couple drivers from online (one from COMPAQ) but neither worked. This is definitely a step in the right direction, though.

by ryan

This is definitely in the right direction. A few days ago I was able to access the CD-ROM drive from booting with Win98 CD. But since then I have lost access to the CD-ROM drive and cannot remmeber what I did before to have that.

by simpsin

lot's of tips but it depends of your knowledge of DOS
first of all. Your DOS boot disk does it have CD-Rom support? if yes all you have to do is "fdisk" the drive to put a partition, format it and copy your CAB files.
if it doesn't, you will have to find the right SYS file and modifie the Config.sys and Autoexec.bat files accordingly
eg:
Config.sys
device=a:\driver.sys /d:mscd000
Autoexec.bat
mscdex /d:mscd000
this will give you cdrom support from the floppy.
there are generic cdrom drivers eg:aspicd.sys that you can find on the net.
for other question email me at simpsin@hotmail.com

by ryan

I am not proficient with DOS. I did try some of the coding you provided but with no avail. I would need a good guide to take this route.

by bill cassada

Okay...if you want to boot and run the 95 setup then put the setup floppy in the A:\ drive and the CD in the cdrom unit. Boot to the A:> prompt and type SETUP.

To install 98 set the BIOS to boot from CDROM and then boot with ONLY the 98 CDROM inthe CD unit. When prompted select "run windows 98 setup from CD" and press

The rest should be handled by windows with only a little interaction from you to select certain customizations. Feel free to email me if you have problems with it.

by paul d. masley

Since you are not proficient in DOS, the easiest way for you to get started is find someone that has a WIN98 startup disk. Boot your computer with the disk. This will give you cd support. Apparently, the disk is already partitioned, if not use FDISK to set your partitions. FDISK is on the WIN98 startup disk. Do not forget to set drive c as active and then format your partitions. Insert your WIN95/98 disk in the cd. It may automatically start or it may not. It it does not start, change to the drive for your cd. Note: The WIN98 startup disk will load a ramdrive. It will move your cd up one letter. In other words, if your cd was drive d:, it will now be drive e:. Once you change to this drive, look for the file setup.exe. Execute this file. Make sure that you have either the product serial number (WIN95) or the key code (WIN98). Uf you are using a WIN98 upgrade, you will need the WIN95 disk. I hope this gets you up and running.

by tmaclennan

What you really need is a "QuickRestore" disk for the Armada 1530. Compaq ships these things with new Armadas. I have one for the 1500 series, but it explicitely excludes the 1530. You should be able to find a local Compaq-certified place that will do that for you, restoring the Operating System and all the Compaq extensions to factory settings.

The hard way to do this is by downloading the Softpaqs from the Compaq support site. Use the following URL and start downloading.
http://www6.compaq.com/support/files/portables/us/locate/3_889.html

by bgriffith

As I said earlier:
"The easiest thing to do is boot from a Win98 startup disk, copy over the Win95 CD to the hard drive, and perform the install locally.

If you don't have a Win98 startup disk, you'll have to find the appropiate drivers for your CD-ROM."

The Win98 Startup disk loads a series of generic CD-ROM drivers made by Oak Tech when you choose "Boot with CD-ROM support". Once you have booted from the Win98 disk, you'll want to copy over the Win95 CD to your hard drive, otherwise you might lose your CD support halfway through installation. (You only need the \WIN95 directory with all the .CABS (e.g. COPY D:\WIN95\*.* C:\WIN95CD))

You won't have to worry about the drivers after the installation either, because if the Oak drivers work, Win9x will automatically install it PnP style when it's run for the first time.

by campbell

ok you said you can find the bios, so go in and set the boot sequence to boot from the cdrom save your settings put the 95cd in and reboot the computer. most pc's now days have a bootable cdrom

by aronya1

Let's make this as simple as possible:

If you are installing Win98, the CD should be bootable. Set your BIOS to boot to the CD, then boot up with ONLY the CD in the drive, and do your install. I have never seen a Win95 CD that was bootable.

If you are installing Win95, or your Win98 CD is not bootable, do the following:
Boot to your floppy disk. These instructions assume that the disk will load CD drivers.
At the A:\ prompt, type: MD C:\WIN95 (enter)
Then type: COPY D:\WIN95\*.* C:\WIN95 (enter) You should see the list of files being copied.
When the COPY operation is complete, remove the floppy and reboot your system to a DOS prompt, using the F8 key. At the C:\ prompt, type: CD\WIN95 (enter)
At the C:\WIN95 prompt, type: SETUP
Windows will begin its install.

You may have to adjust your drive letters to correct for partitioned drives, etc., but this is the best method I've found for installing Windows.

Good luck.
Tim

This discussion is closed to new replies.