31 replies
by skiz
well you can try to reset the BIOS back to 'failsafe' default values... and see if that works.
If not did any software change, of get installed?
If the BIOS default settings dont work I would try to get the latest BIOS patch and flash it and then set it back to the default values and see if that cleans it up.
Is this system always on? It may be a heat problem.
good luck
by tlefort
by syscokid
I suspect overheating as well. Especially since you're not getting any beeps or error messages from hardware or software. Make sure the Power supply fan and CPU fan are running. Leave the cover off and powered down for awhile, then try again.
Either that or your motherboard is totally fried.
by tlefort
by bstei18
Is there a machine similar to yours around that you can test with? If so, pull the hard drive and see if you can boot to safe mode easily. Don't let it boot normaly or Win95 will try to install any device that would be different on this machine. If it works you've probably eliminated that as a problem and can look at the motherboard/BIOS.
If you can get to the motherboard manufacturers web site see if you can download a BIOS flash and try it with a backup of your boot disk. While this may bewishfull thinking, it may work.
If that doesn't work it is probably a bad MB or processor. If you can get the same board and the test with the HD worked, you may not have to reinstall too much.
Good Luck!
by tlefort
by spiceman
There could be several things wrong so you need to eliminate 1 problem at a time. You did not say when you started having these problems - after what event.
Try:
remove all other cards except video and see if that works. Do your Windows 95 installand then add one device at time to find out what was the offending device or driver.
If you had problem just with the video and memory do you have another memory module you can try and ensure as stated earlier all the cooling devices are working correctly. One try is just to swap the memory between the slots so that you are making sure they are not slighty unaligned. Also can test if the memory modules work okay on another computer.
Another thing to try is to change the video card, keeping the memory the same (remove all other cards).
You can also try to check the web site for BIOS upgrade - ideally you should do this first!
run scan disk from your boot disk and if possible a virus check (boot sector viruses).
Good luck,
Kamal
by tlefort
by calves
Call me crazy, but your master boot record might be corrupted (Although I agree with asyscokid about overheat). This will not hurt your computer:
Boot from the w95 boot diskette, see if you can use the keyboard this time and at the prompt run fdisk /mbr.
I also agree with previous answer on reloading the defaults on Bios.
Good luck!
by tlefort
by bblunden
I don't think its a heat problem. Things are happening too fast for it to be a heat problem (it has had time to sit and I am assumming he didn't lose a fan).
I am leaning more towards a virus or a memory failure.
by tlefort
by cindycyn
by tlefort
by melodyj
Your display driver would do this... go into safe mode - choose to not load all windows drivers. change your display to the generic driver and put it in vga mode.
Good luck,
Melody
by tlefort
by reghakr
To see if Explorer is the problem, try this:
Hit F8 on startup, and choose Command Prompt. Type edit c:\windows\system.ini Under
[boot] Change
shell=;Explorer.exe
shell=progman.exe
If Program manager loads go to File>Run, type msconfig, goto the Startup tab and uncheck everything. To get to Device manager type control sysdm.cpl in the Run box.
Either go back and change system.ini to the original or if you're comfortable using File Manager, you can type Winfile under the File>Run and check your configuration files.
Hopefully this will get you back in.
Jim
by tlefort
by slogmeister
I smell a virus. Boot with a known-virus free boot disk and run a virus scan of the boot sector of your hd. Then, scan the entire hd. This really sounds like a virus to me.
- Jason Eberhardt
by tlefort
by mogge
Make a backup on all your importent stuff.
Boot whit a disk, and fdisk your hdd. Reinstall Win95.
Or try to change the I/O.sys file.
Make a bootdisk, (if you don+t have one)
Type Attrib i/o.sys -h -s -r
delete the file
copy the I/O.sys from the floppy and reboot.
It may help.
good luck...
by tlefort
by 9878445
by tlefort
I'm sure one (or more) of the above is the answer. Variation of above. Take the top off, and look to see if the fan has not fallen off!, or is connected to the power supply.
If not, there we are looking for something silly. Things to check: How much RAM is reported during boot up (Does the amount vary). Is Post reporting the correct processor speed (Try under-cooking the CPU for a while).
by tlefort
by david.lange
by tlefort
by arg cio
by tlefort
by tlefort
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending