Discussion Locked

Windows2000 SP2, Abit KT7A & 1 GB RAM

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,
I need to install to my Windows2000SP2 1 GB RAM. The Abit KT7A supports 1,5 GB RAM, but after installing the boot process is stopped with a BSOD that system couldn`t find file or registry hive system32\config\software... With 1x256 and 1x512RAM modules it works fine, but with 2x512 RAM modules it doesn`t boot. Any idea?

20 replies

by dmiles

1)Check the memory modules to make sure that they match,speed,type etc.
2)Check with motherboard manufacturer to see what is the maximum amount it will support,it may require switching jumpers on the motherboard
3)You can try switching the memory in the banks used,put the new memory in bank 0 and other module in bank 1

by borisporosin

All this I tried before. Windows2000 SP2 is unable to run with more than 512+256 MB of RAM. The motherboard detects that I have 1 GB of RAM.

by @lberto

That's a weird issue. I am running a Data Center, with Data General servers. 4 Gbytes RAM, Windows 2000 Advanced Server and Windows NT Terminal Server 4.0 latest SP both and no problems. I checked MS and this is what I found, this could help you.Check MS Article Q292934

@lberto
alberto@pancarib.com

by montea7

Since I am not sure what version your board is and do not know which bios version you are running:

I would check for a newer bios as there were some instabilities in the earlier bios that were corrected

Try conservative memory settings in the bios:

DRAM Clock set at Host CLK
Enhance Chip Performance - disabled
Force 4-way interleave - disabled
Enable DRAM 4k-Page Mode - disabled

Bank x/y DRAM Timing on SDRAM 8/10ns or Medium

DRAM Bank Interleave on Disable
MD Driving Strength - try HI and LO
SDRAM Cycle length on 3
Fast R-W Turn Around on Disable

by borisporosin

Great!!! Thank you! The Setting
Force 4-way interleave - disabled
Enable DRAM 4k-Page Mode - disabled
helped me. Thanks again.

by berserker

Have you tried flashing the motherboard BIOS to the 4A version?

make sure that you have the same memory module installed into the SDRAM slot.

What is your memory brand ?

by jesselou

if you put your 2x512 ram modules go to your cmos upon restart to see if they are detected in the bios areas, disable quick boot in your bios and observed the memory count before the operating system loads.if the 2x512 is not recognized during the post then it could be possible that one of your ram module is defective and to isolate it you have to put one by one your memory modules to singled out the defect.

by curacao_dejavu

Hi,
I made a compilation of possible steps to troubleshoot this.
First take a look MS KB Article ID: Q104203, it is mention mt 3.1 but it's the only item in the kb mentioning the problem you are describing.
I would check if the memory are listed on the ms hardware compatibillity lis. (www.microsoft.com\hcl)
Second from abit's website I got:http://www.abit-usa.com/eng/faq/kt7a.htm

Why can't I boot from a SCSI CDROM attached to Adaptec 29160 SCSI card then install operation system onto assigned hard drive? Or fail to start Windows with Adaptec 29160 SCSI card plugged on KG7-RAID mainboard? (KG7 / KG7-RAID / KT7A / KT7A-RAID / KT7 / KT7-RAID)

and also
http://www.abit-usa.com/eng/faq/common.htm
how to install the os.

in summaryI would upgrade the bios, and make sure every device is on the hcl of microsoft, if you are using athlon look up the fix and scsi provide the drivers yourseld instead of letting w2k provide the drivers.

Masha exito,

Leopold

by curacao_dejavu

try can try to install the recovery console to help you.(if you didnt yet)
Q229716 Q238359 Q156640 Q269075

Also what I am not sure off , did you install w2k also right away with 1GB.
If so, see the 1 posts, if not install with 1GB.

if none of these are helping :( can you post the full error message.

Leopold

by curacao_dejavu

last item, if your mother board has a setting called "defaults" , usually f6, or something similar use that.

by borisporosin

Sorry, didn`t helped me.
The error message is on the BSOD:
STOP C0000218 {Registry file failure}
The registry cannot load the hive (file):

...

by borisporosin

OK, here is my configuration for better understanding:
Abit KT7A motherboard
Thunderbird 800MHz
1x WD 20 GB
2x WD 60 GB
Adaptec AHA2940UW SCSI + SCSI CDROM + SCSI Teac Writer
Umax 1220S (scsi scanner)
300 W power supply
ups (not monitored from computer)
17" monitor
Win2K SP2
HP DeskJet710C

The BIOS detects the 1 GB of RAM, but windows doesn`t boot with them.

by borisporosin

The error message is on the BSOD:
STOP C0000218 {Registry file failure}
The registry cannot load the hive (file):

...

by borisporosin

The error message is on the BSOD:
STOP C0000218 {Registry file failure}
The registry cannot load the hive (file):

...

This discussion is closed to new replies.