Discussion Locked

WLAN with Cisco Aironet 1230's

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Our Director of IT recently purchased several Cisco 1230 WAPs. I am a novice with Cisco products, but I was able to get the first bunch up and running. We are currently only using WEP for encryption and I know that that's not enough. I am the administrator for a NT 4.0 domain, with several win 2k member servers. We have a three building campus with 2 subnets.

I would like to increase security by implementing WAP however some of my laptops don't have drivers that work with WAP. My boss is talking about implementing VLANS and restricted guest access and I am clueless. It seems to me if all we can do is implement WEP than VLANs are pointless. He also wants seemless connectivity between subnets-so I guess using a vpn would not work. I would like for the WLAN to prompt people for a password, to be able to assign access rights via people's membership in their respective NT Groups. I would also like something similar to Starbuck's where a website pops up and asks you if you want to access the wireless lan. Do I need to get more equipment or what? I have no idea where to begin. Any suggestions you might have would be most helpful.

4 replies

by charles_j_smith

Sounds like you really need Aruba Network gear.

As far as Cisco goes, not sure if they support authentication over a web page (Aruba does). I think there is another company that makes this solution, but I can't put a finger on it yet. I'd rather have it all in one shot.

Aruba also creates a firewall per client when they are on the wlan. Cisco does not (that way you don't really need to segment traffic using vlans (they can be more headaches).

Aruba has several different types of guest access available.

I'd research Aruba - although they are pricey, but well well worth it. Cisco's not there yet...

by mshavrov

All, what your boss talks to you to do - connect Access Points to separate VLAN. You should:

1. Create dedicated VLAN on your switch(es)
2. Create appropriate interfaces to route to this VLAN,
3. Configure ports, where you have these access points to this VLAN.

Then you should configure appropriate security on this interface (access-lists, firewalling, IDS, MAC address filtering, etc.). This will at least limit access to your LAN.

To authenticate users, who access your WLAN you should install firewall with "authentication proxy". Your users may access certain web page, get authenticated, and then they will have access to your network.

Another thing you may consider is using LEAP (Cisco's Wireless security protocol), or some kind of "dynamic key change encryption". This may require installing Cisco Security Server.

Also you may install VPN server with one interface in WLAN network and another interface in LAN. Anybody will be able to connect to wireless network, but only users with VPN software and only who have VPN authentication will get into your LAN.

So, as you see, there are a lot of ways to do this. If you want to get more detailed information - send me e-mail.

Good luck,

Michael Shavrov
CCNP, CCDP, CCSP, Checkpoint CSSA, MCSE W2K, Sun SCSA, Security+

by Former member

I would upgrade the code or equipment on the WAPs. THey will then be able to run with the following features:

Wi-Fi Protected Access
Wi-Fi Protected Access (WPA) is now supported on Cisco Aironet access points. WPA is the Wi-Fi Alliance specification for interoperable wireless LAN security. It supports IEEE 802.1X authentication using extensible authentication protocol (EAP) authentication types and temporal key integrity protocol (TKIP) encryption.

802.1x would be your answer to authentication. It also supports ROAMING VLANS!

IEEE 802.1X Local Authentication Service
This feature allows a Cisco IOS software enabled device to authenticate wireless clients when connectivity to the AAA server is not available. It incorporates an IEEE 802.1X enabled RADIUS server that supports EAP authentication types into Cisco IOS software. This allows the Cisco Aironet access point to authenticate wireless clients when the wide area network (WAN) link is down or the RADIUS server at the central site is not available. This provides remote site survivability by allowing an access point to continue to access local resources such as file servers or printers in remote site deployments with non-redundant WAN links.

Wireless Domain Services
Wireless domain services (WDS) is a collection of Cisco IOS software features that enhance wireless LAN (WLAN) client mobility and simplify WLAN deployment and management. The WDS feature set supported in this release includes fast secure roaming and IEEE 802.1X local authentication service.

Be sure NOT TO USE cisco's LEAP authentication protocol as it is highly vulnerable to remote, brute-force attacks.

Here's a cionfig example for Aironet:
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c0912.shtml

This discussion is closed to new replies.