Discussion Locked

Write Hard drive to zeros

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
How can I write zeros to the primary hard drive?

14 replies

by dmiles

You are attempting to do a low level format which is not recommended,because it causes problems when you attempt to partition and reformat the drive.

Low-level foramatting is done by the drive manufacturer,check the drive manufacturers web site for drive utility.

by timwalsh

I assume what you are trying to accomplish is to ensure that nothing sensitive remains on the drive.

There is no method built into Windows to do this.

You could use a hex editor or disk editor to do this, but this probably isn't the most efficient way.

Your best bet would be to acquire one of the many disk wipe programs available on the market. Some of these programs will allow you sto specify the character to use to over-write (wipe0 the entire disk. A better bet is to choose one of the programs that offers what is commonly known as a DOD-wipe. This type of wipe is used by the US Dept. of Defense to wipe classified hard drives. Essentially, this type of wipe overwrites your drive several times (usually 3), each time with a different character. For the super paranoid, there are several even more powerful wipe algorithms available that will overwrite a drive 25 or more times.

If you run a Google search using the keywords "disk wipe" or "dod wipe", you will come up with numerous vendors offering this type of product.

by modady

Tim thank you for responding...I didnot sensitive information on the drive, but stability problems with the operating system caused by the drives wear and tear. Which I still have problems with fixing.

Again thanks for your help.

by kelleytak

I have used a few wipers and have always had to go to mfg's site to get the booters.

Will this tool allow me to clean the drives without having to spend the time? (I'm tired of searching for the files)

by jschein

DMILES is correct. 0's are a low level format. Not recommended unless you have done this before and know what you are doing.

Most drive manufacturers have specific software for doing a low level format that may or may not work on other drives. Visit their websites and see what there is available to you.

If that doesn't help and you need to do a LLF, search google for "LOW LEVEL FORM"+download and you will find a plethera of LLFs to download. I am assuming your drive is just a paperweight and you just want to try and get back to using it.

Lastly, you may just want to visit the website of the manufacturer and fill out their RMA and request a replacement. After you type in the serial #, it will tell you if it is covered for free or not.

Good luck.

by oz_media

I've used ZAP before and it works well BUT I would highly recommend using a Disk Wipe utility. Even Norton Utilities has a so so version of this. Sounds like your quite paranoid of your data, unless it is criminally implicating, I wouldn't worry about writing zeros.
Many people flatter themselves by thingking someone may go to great effort and possible expense to recover data, unless your storing your banks list of credit card numbers and passwords, I wouldn't be so concerned and a standard disk wipe utility should suffice.

by wcp

You can low level format (or write zeroes) by running utility software (SW) from your hard drive (HD) manufacturer.

Most of the brand name manufacturers, Maxtor (Quantum), Western Digital, Seagate, Samsung, and Fujitsu (IBM) provide utility SW that does HD diagnostic test and low level formatting.
The one exception is Toshiba. It does not provide any utility SW for general public.

Low level formatting is very straight forward. You just download the SW, which make a bootable floppy or even CD, and boot from it and follow the instructions.

To be safe, disconnect any other HDs before doing the low level format.

Low level formatting is sometimes very desirable in following instances:

1). HD diagnostic test showed that there were some bad sectors and it said that they can be repairable.
I have done this and it worked on a few occasions. Some manufacturers (IBM) may require a user do low level format and diagnostic test before sending the HD for RMA.

2). HD diagnostic test passed but you want the HD as clean as possible before installing Windows (or other OS).
This may be a HD that is rather old (less than 8GB).

3). you want to wipe out all partitions (FAT, NTFS, Linux, and so on) and data.
There are easier ways to wipe out all partitions. If the data is very important, then destroying physically is the way to go.

Post a comment if you need more information.

by wcp

It should have been "Fujitsu, Hitachi (IBM)" not "Fujitsu (IBM)".

by sheg101

If this is to reformat, get the utility from the manufacturer as said by other respondents, if this is for security, then even writing to zeros does not solve the problem as there are apparantly stuff out there that can read the slight magnetic difference between a zero that was a zero and a zero that was a one.

I would suggest getting the freeware "active killdisk" from lsoft.net. This writes zeros and random data 3 times to the whole disk.

by lanwanman352

Assuming that it is an IDE drive, and that you want to be able to use the drive again after zeros are written to it . . . determine the manufacture of the drive, visit their website, and download their recommended hard drive diag software. Most of these diag software packages provide a way to write zeros to the entire drive.

For a FREE software tool that will completely remove sensitive data from your hard drive by overwriting it several times with sophisticated patterns, try "Eraser"

http://www.snapfiles.com/get/eraser.html

by ozi eagle

Hi,

I find that the POWERMAX utility from MAXTOR does a good job on most brands of drives. Free to download from their site.
You create a DOS bootdisk to run it.

As others have suggested disconnect any other drives before using - can save a very nasty mistake of wiping the wrong drive.

After the wipe you will need to FDISK the drive (use old win98 startup diskette). Format with the OS you are using.

Herb

This discussion is closed to new replies.