Question Locked

XP startup hangs at kmxstart.sys

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I've seen maybe two posts about this problem around the web, but can't seem to find any useful tips at a fix.

I'm working on a family member's HP Pavilion running XP SP2.

No matter which mode I boot in, it hangs at the same point, then the screen goes blank. It does not restart.

Booting in safe mode revealed that the offending driver is kmxstart.sys. A little research indicates this file is affiliated with a possible CA vulnerability, but I have no idea if these two problems are connected.

Recovery Console (I ran chkdsk /r) did identify and fix some things, but the problem persists.

Thanks in advance for any advice you guys may have.

12 replies

by rob miners

Status and Recommendation:

CA has addressed this issue by providing a new automatic update on January 22, 2007. Customers running one of the affected products simply need to ensure that they have allowed this automatic update to take place.

I am sure that it would have been updated by now but not knowing the history of the PC I don't know. From what I have seen in other posts it has been Viral. It won't hurt to try this anyway.

Can you use msconfig in Safe Mode to disable it from starting by unchecking the box next to kmxstart.sys or if you have access to the CA software and install key uninstall, CA and reinstall it again later.

If you can then access your PC turn off System Restore.

Download Malwarebytes Anti-Malware.

http://download.bleepingcomputer.com/malwarebytes/mbam-setup.exe

* Double-click mbam-setup.exe and follow the prompts to install the program.
* At the end, be sure a checkmark is placed next to Update Malwarebytes' Anti-Malware and Launch Malwarebytes' Anti-Malware, then click Finish.
* If an update is found, it will download and install the latest version.
* Once the program has loaded, select Perform Quick Scan, then click Scan.
* When the scan is complete, click OK, then Show Results to view the results.
* Be sure that everything is checked, and click Remove Selected.

Just to be on the safe side when you finish do an online scan with Bitdefender.

http://www.bitdefender.com/scan8/ie.html

Remember to turn on System Restore when you have finished cleaning.

Update your Antivirus software.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by rsitech

Jacky -

I think you are definitely on the right track, as I would not be surprised if this PC didn't receive the January 2007 CA update. Implementing your advice is challenging in that the machine won't even boot in safe mode in the first place. That's where I noticed it was hanging at kmxstart.sys. It then simply powers down.

One thought I had was using the RC to uninstall CA through the DOS prompt, but don't know if that's even possible.

Anyone know if, in the absence of being able to boot into safe mode, a program can be uninstalled throuh DOS?

Thanks again for all the help.

by rob miners

to boot to the Recovery Console to a Command prompt and be able to rename that file. I haven't actually tried it but it may work to get you back into Safe Mode to uninstall CA.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by Former member

Google the title and follow the links.

The problem could be a malware infestation or it could be a hardware issue; it depends.

by gcollier

Something you may want to try is to take the hard drive out and put it in another working PC. Then see if you can delete that driver file.

Also have you tried booting the system using last known good configuration? Sometimes that will help - although it can be a bit of a long shot.

Lastly, if all else fails - put the hard drive in another box, copy the data and reload Windows.

by rsitech

Jacky,

Your advice was sound. I was successfully able to rename the kmxstart.sys driver in DOS. Unfortunately, on the very next boot attempt (in safe mode) the system decided to hang at the NEXT PRIOR driver in the boot sequence, mup.sys. I then changed this file name in DOS, booted again in safe mode, and saw the NEXT PRIOR driver, serial.sys, cause the system to hang once again.

Does this sound as unusual to you as it does me? I envisioned the boot sequence skipping right over kmxstart.sys and giving me my first view of safe mode in a long time. I was wrong.

Thanks once again.

by rob miners

Make sure that ACPI, Plug & Play and USB are all enabled in the BIOS.

Disconnect everything bar the Keyboard and Monitor. Don't have a Mouse or any USB or other Devices connected.

Try booting into safe mode.

If you have access to a DMM (Multimeter), Check all the power supply voltages and try to watch each as you try to boot. If they are more than 7% below normal and\or your PSU is over 5 years old, less than 350W and you have a 3D gaming graphics card with 128MB or more of graphics memory. Consider replacing the power supply with an upgrade of 500W or better.

If you have PCI, PCI-E or AGP Graphics card and also have a video connector on your motherboard try taking out the graphics card and run off the motherboard video. Remembering to ground yourself by placing the back of your hand on the Power Supply Unit and not moving your feet. By not taking this precaution it is possible that you could inadvertantly cause damage to the PC from an electrostatic discharge. Be sure to adjust your BIOS accordingly

Try moving the RAM to different slots. remembering not to touch the golden edge of the memory stick. Check with one stick at a time, remembering to disconnect the power from the PC.

Check the memory.

You can test the memory by running Windows Memory Diagnostic that can be downloaded from http://oca.microsoft.com/en/windiag.asp. If memory problems are found, try re-seating the RAM. If it doesn't work, replace the defective RAM.

You could also try a Repair Install.

To reinstall Windows XP by starting your computer from the Windows XP CD, follow these steps:

1. Insert the Windows XP CD into your computer's CD drive or DVD drive, and then restart your computer.

2. When the "Press any key to boot from CD" message appears on the screen, press a key to start your computer from the Windows XP CD.

Note Your computer must be configured to start from the CD drive or DVD drive. For more information about how to configure your computer to start from the CD drive or DVD drive, see your computer's documentation or contact your computer manufacturer.

3. You receive the following message on the Welcome to Setup screen that appears: This portion of the Setup program prepares Microsoft Windows XP to run on your computer:

To setup Windows XP now, press ENTER.

To repair a Windows XP installation by using Recovery Console, press R.

To quit Setup without installing Windows XP, press F3.

4. Press ENTER to set up Windows XP.

5. On the Windows XP Licensing Agreement screen, press F8 to agree to the license agreement.

6. Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP.

Note If Windows XP was preinstalled on your computer, and you do not have the Repair option, contact your computer manufacturer to make sure that you have the installation CD for a repair install.

7. Follow the instructions that appear on the screen to reinstall Windows XP. After you repair Windows XP, you may have to reactivate your copy of Windows XP. You will have three days grace with a lot of Nags. ;)

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by rsitech

Guys, I just wanted to say thanks for all the help. In the end, what actually ended up working was a hybrid of all your advice.

After RC could not immediately fix the problem, I tried using DOS to rename the driver file, hoping the system would skip over it at the next startup. Didn't happen.

I then removed the drive from the notebook, plugged it in via USB to another notebook, and immediately scanned it with Malwarebytes. Several trojans were identified and removed. Plugged it back in. Attempted startup. No luck.

I removed it again, but this time I deleted (not uninstalled) every trace of CA software I could locate, hoping to kill just enough of it to allow me boot up. This ultimately worked, but my new problem was because of all the deleting I did when the drive was attached via USB, I was unable to perform a proper CA uninstall (preventing me from installing new AV software). This was quickly fixed by downloading and running CA's uninstaller, which cleaned up the remnants.

The notebook is now back in working order.

Thanks again for all your advice.

by narapriya

I'm running into a similar issue on my HP pavilion laptop. Can you tell me the list of CA software files that you had deleted that got your system booting again? I deleted kmxstart.sys and the CA directory in the HD but now my laptop reboots at Mup.sys just like yours...Thanks!!

by philippe s

I had the problem with CA Security Center 3.2.1.19
I did the following
1. boot safe mode with console
2. start explorer
3. Start CA Security Center
CA complains Anti-Virus and Anti-Spyware need attention
4. Fix Anti-Virus in Security Center => trigger a reboot

Et Voila, my machine works fine now.

This discussion is closed to new replies.