Discussion Locked

3.2 Floppy drive has activity for no rea

0 helpful
30 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

We are using our home PC loaded with Win 98 and the floppy drive starts a accessing. There is no disk in the drive and I have not asked to open the drive or save info. After a few minutes it goes away. Then later it happens some more. I have F-Disk the hard drive and done a total reload. I have traded out cables. I have traded out floppy drives. I am at a loss. Please help!
The system is this. Win98/AMDK6II 450 MHZ/128MB SDRAM/13gig wester digital hard drive/52xCDROM/ZIP/CD R/W/R 4x 4x 24x /floppy 3.2/TNT 2 AGP 32MB video card/Space walker mother board.

30 replies

by syscokid

Here's a shot in the dark: Power is shorting. Try a different powr cable and see if it helps.

by doc7213

Try switching the power cable to the floppy inside of the system. You might be having some problems with the power supply.

by mphoffar

This actually sounds like findfast trying to index the floppy drive. Try removeing that from the start menu or run and run services in the registry.

by steveh

This happened at my college. An entire shipment of computers had bad floppy drives. They just had all the floppy drives replaced. This was the only fix for them. The only other way to stop it is to leave some disk in the drive at all times afterboot up. I wish I had a better answer, but you just got one of the faulty floppy drives. Sorry.

Hope this helps. Good luck!

by lazerwolf

Jack,

It could be hardware oriented, but I've run into this frequently at work and it has always been when we are running MS Outlook 97/98/2000. If you are not running MS Outlook skip the rest of this message. If you are, Outlook has a "Journal" option that tracks the files that are accessed for certain applications. While Outlook is open, it will apparently "check" to see where the files are that have been listed in the Journal. If you have ever accessed certain types of files on your A: drive, the Journal will try to verify there existence by accessing the drive.

To turn this off, you need to go to the Journal in Outlook and delete any applications that are listed there. Then check in the Tools|Options menu under the Preferences tab, click the "Journal Options..." button (at least in Outlook 2000), and unselect any applications that are selected.

If this sounds like the problem but is too confusing, feel free to email me.

Good Luck.

by bdgray

MS Find Fast is your best bet. Remove it from the Startup folder. Also, if a user has recently opened a document from a floppy disk by double clicking on it, a shortcut to the file will be in the Documents folder on the start menu. MS has noted that this can cause randoms floppy seeks. To get rid of it go to START | SETTINGS | Task Bar & Start Menu. click on the Start menu programs and click on CLEAR.

Hope this helps.

by homer simpson instructor at large

I have had a similar problem on several machines. My culprit was Findfast. When it starts accessing the A drive do a Ctrl Alt Del and see if Findfast is trying to read the A drive for some wierd reason. Uninstalling it fixed it for me.

good luck

by clover252525

Click on START/RUN and type REGEDIT.

Go to HKEY_CURRENT_USERS\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer.

Find the setting (in the right hand frame)called NoDriveTypeAutoRun, click on it and click on MODIFY. Change the Binary Value to: 0000 95 00 00 00

Exit Regedit and reboot. The PC won't seek the floppy needlessly any more.

Needless to say, before ANYTHING else, make sure you back up your registry!

clover

by qhcomputingny

Check the floppy drive cables inside the computer and make sure that they are installed correctly. The red marking down the side of the cable has to be aligned with Pin 1.. If not the light on the floppy drive will remain on constantly, if you are using it or not.
Hope this helps.
Eddie

by >@ >@ gone fishing @< @<

It is most likely a base application that you have running. Ie: Find fast that has been well covered by other posts. Do you have a VIRUS Scanner Installed, with a Autoprotect feature, this feature will cause the Virus Scanner to Periodically check your selected drives. I think you should re-load you system again, but add application on a One at a TIME basis. Find out exactly what you are insatlling to make this happen.

by dmiles

Sound like an intermittent problem that could be caused by over heating.Another thing check the anti-virus that you are running and make sure it is not set to check drives.You also have a lot of drives connected togeather and one could be causing a problem accessing the floppy.

by farhan

hello
well you r running lots of thingson your computer and there could be some problem with power supply. pls try changing the power cable of computer and for floppy inside the computer..
or the other thing seems that find fast is try to find floopy and may be this is causing problem try after uninstalling it..or see if u have any program that uses ur floopy like may be virus scanner that try to clean your floopy drive and that is why it is doing this problem..
these were the possible things
Hope this will help you
Bye

by ec364

Remove drive A: from being indexed in FindFast. Follow this:

(1) Click Start/Settings/Control Panel
(2) Double-click on Find Fast icon
(3) Highlight drive A: from the list by clicking once
(4) Click Index from the horizontal menu
(5) Click "Cancel Selected Task"
(6) Click OK
(7) Close FindFast

This won't include drive A: in the index. You could also change the time interval, in hours by clicking Index/Update Interval.

Enjoy!

by rodney (tsg)

I know this doesn't jive with common theory, and since you have said you have replaced the drive itself this may not be your answer. But I have run accross this problem before on an old Dell 486/33 that I was building for my son. I was frustrated tono end and about to toss the system out the door. Just for the heck of it, I reversed the cable. Yes, put the red strip opposite the #1 Pin. It worked like a charm. Don't ask me why cuz I couldn't tell ya. But it worked.

This discussion is closed to new replies.