Discussion Locked

98 won't boot

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

when booting you get CPU is unworkable or has changed - Please recheck CPU soft menu.
I've reset it to fail safe defaults it comes up the same. When I push F1 it tells me Disk Boot Failure Insert system disk. This doesn't work so I insert a windows98 startup floppy. When I type at the A: prompt FDISK /STATUS it tells me that: No Fixed Disk is present? Does this mean that the hard drive is shot? Please Help! A MCP isn't any good without the hands on!

15 replies

by >@ >@ gone fishing @< @<

MCP - More Capital Please.
I think your mainboard could be on the way out, is your Hard Drive detected in the Bios, check your standard Bios options to ensure it is listed correctly, your system summary screen at start-up will also tell you if it can see a HDD. You should be concerned with the CPU error, have you had any power surges or major faults on the system.

by klvrcn

I think the awencer: MCP-More Capital Please: by:>@>@Gone Fishing@<@> is really inapproiate!! At least I have my MCP! 3 to be exact. Pro, Server & AD 2000, all I can say is I am trying. And may need assistance along the way. I thought that was what Tech Republic was all about? Helping people with technical problems. Please correct me if I'm wrong

by richard lane

Firstly, Techrepublic is about techies helping other techies, that's the whole point. Trying to dig at others who have qualfications yet need help boils down to nothing more than petty jealousy - there is no place for that here.

On to your problem:
1) The first thing I would check is that all the connectors and cables internally are seated properly, this can often cause problems accessing HDDs.
2)To eliminate/confirm and HDD problem, try putting it into a diferent machine and see if youcan access it there.
3)The CPU error may be caused by overheating - check that the cooling fan is still working properly, and hasn't become clogged with dust etc.
4) If the HDD can be read in another machine, and all the other checks are fine, then it looks like the motherboard may well be on the way out :-<

HTH

Richard

by soekratis

The message that you describe indicate that there were some changes to the CPU soft menu (BIOS Setup Menu). This is not because you have change it but rather the last settings saved on the BIOS include the HDD settings. Therefore, when you boot thesystem and BIOS could not find your HDD, it assumed that you have made some changes. The information that you have provided indicated quite obviously to be a HHD failure. To look under the hood of the CPU could be quite off-putting experience if you are not all to familiar. If you know how to get to the BIOS Setup, get in there and you may find some information about your system. As suggested by ANS-1, check if the BIOS could detect your HDD. Some Bios or rather most new BIOS auto-detect the components that is connected to your system. If no HDD can be detected, i suggest remove the HDD and bring it to a repair or computer vendor and have them verify before buying a new HDD.

good luck
regard
Soekratis

by rg11

I had a simular problem. The processor was bad and also the power supply wasnt giving a constant power so I replaced that also. Everything works fine now.

by ann777

Yes, this forum is about helping. I have an MCSE in NT, and will be working on 2000 -- but really have not started yet. I've not been through A+, but have learned a great deal about hardware by doing. You'll get there; don't bother with the people who make jabs at you.

I've also seen this problem with a bad hard drive -- or specifically, a hdd that was intermittantly powering down then back up again.

Look at cables -- make sure that everything is secure.

Look at the bios -- Press F2or whatever it takes to get into "setup". Make sure the bios sees the hdd

Look at the power supply -- and isolate the power to the hdd (ie. verify that no other devices are using that power branch)

If you still get the same error, I'd recommend taking the hdd to another computer and testing it on another computer. Then you may eliminate the hdd as the cause.

Keep swapping the hardware, until you can narrow down the parameters.

by ann777

The other thing you should check is the battery. If the CMOS battery is drained, than that could cause the CPU settings to be lost.

by buffalodan

Gone fishin's MCP dig was not aimed at you, it was aimed at Micr$oft...you need not be offended.

Have you verified the CMOS Battery's health?

Also, flashable bios can become corrupted.
I would research BIOS updates for this bios/mb combo,

and yes, it's a good idea to test that hard drive in a second machine...

best of luck, never be afraid to ask...I am not...

Dan T.
MCSE
A+
CCNA

and still chuggin along since 1981....

This discussion is closed to new replies.