17 replies
by jlstrauss3 Accepted solution
by thumbsup2 Accepted solution
by jlstrauss3 Accepted solution
by thumbsup2 Accepted solution
by deadly ernest Accepted solution
corrupted and needs to be rebuilt. I used to do this occasionally using a DOS command after booting from a WIN98 Boot disc, but not sure how that will work on one of the bigger modern hard drives as I haven't tried to run that version of DOS on a system with anything bigger than a 40 GB g hard drive.
The command was, from memory, Fix MBR - I usually selected from the various help options I got after loading the DOS into RAM.
by jlstrauss3 Accepted solution
by deadly ernest Accepted solution
OK, the only time I've ever seen a deive NOT recognised in the manner you mention and it's NOT been a MBR issue and the other partitions on the drive are recognised, it's been a case of the drive format NOT being recognised by the operating system boot code.
Two things to check, which you may have done but not mentioned yet.
Can you run FDISK, if so, does it show the C partition as being formatted and as being set to ACTIVE.
If it's not set to ACTIVE, set it to ACTIVE. If it doesn't recognise the format, you could be in big trouble.
Best thing is to get a LInux Live CD that reads NTFS and FAT32, then examine the disc using Gparted or a similar program to determine the active status and the partition format.
If there's no data on C you wish to recover you can skip this and try a format C; and OS reload. But I think that's where you're headed now. I recommend the Linux Live disk to recover data or remove the drive to be a secondary in another system to examine it through that one.
by rob miners Accepted solution
Check the memory.
You can test the memory by running Windows Memory Diagnostic that can be downloaded from http://oca.microsoft.com/en/windiag.asp. If memory problems are found, try re-seating the RAM. If it doesn't work, replace the defective RAM.
You can use the Hard Drive Makers Testing Utility to Test the Drive which can be downloaded from below.
Hitachi / IBM
Western Digital
Fujitsu
Seagate
Samsung
by rob miners Accepted solution
The drive is being detected in the BIOS
The hard disk or the hard drive partition is damaged.
Sector 0 of the physical hard disk drive has an incorrect or malformed Master Boot Record (MBR).
An incompatible or damaged partition is marked as Active.
A partition that contains the MBR is no longer active.
To mark the Partition as Active. Boot from your XP CD and press the first R to enter the Recovery Console.
At the recovery command prompt type in these commands pressing the Enter key after each one.
diskpart
select disk 0
select partition 1
active
Now type
EXIT to exit the diskpart session
fixmbr
fixboot
Restart the PC with the XP CD removed.
Take note of any errors that you may encounter and let us know.
by jazzzman71730 Accepted solution
by breezer85 Accepted solution
... Tried various solutions but to no avail. I just swapped out the HDD and started from scratch! If you have important data i suggest you try and connect it as a secondary/slave drive and see if you can recover any data!
Sorry i'm not much help but it certainly saved faffing about!
by alxcsby Accepted solution
Pull out your trusty XP CD and do a repair reinstall, just on a whim.
1.
When the Press any key to boot from CD message is displayed on your screen, press a key to start your computer from the Windows XP CD.
2.
Press ENTER when you see the message To setup Windows XP now, and then press ENTER displayed on the Welcome to Setup screen.
3.
Do not choose the option to press R to use the Recovery Console.
4.
In the Windows XP Licensing Agreement, press F8 to agree to the license agreement.
5.
Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP.
6.
Follow the instructions on the screen to complete Setup.
by daveaaa3 Accepted solution
by benc Accepted solution
by peconet tietokoneet Accepted solution
1. Enter Windows XP Recovery Console.
2. http://pcsupport.about.com/od/fixtheproblem/ss/rconsole.htm,
When you reach the command prompt
(detailed in Step 6 in the link above)
type the following and then press Enter. fixmbr
3. The fixmbr utility will write a master boot record to the hard drive that you're currently using to boot into Windows XP. This will repair any corruption or damage that the master boot record may have.
4. Take out the Windows XP CD, type exit and then press Enter to restart your PC.
Assuming that a corrupt master boot record was your only issue, Windows XP should now start normally.
by chi-7 Accepted solution
1 stupid question, If a Linux utility dosn't read the partitions, can you hear the platter drive spin up?
With old technology drives "head stiction" on the landing
zone was a common problem, especially if the machine
was exposed to wide ambient temperature variations,
allowing condensation.
Put a pencil or screwdriver to the drive housing and to
your ear and power up, you will hear the platter spin up,
if you don't, power down and pull the drive, reconnect
the cables and power up, then give the drive housing a
sharp CW and CCW rotation. ( naturally on axis with the
platters)
The inertia of the platter asm. Will break any
"Head stiction".
Drive ID read by BIOS is a function of the IDE board
on the drive, no platters, no MBR, no partitions.
If this is the case replace the drive and clone it using a
utility such as acronis Disk Director or Ghost
by 1bn0 Accepted solution
It really sounds like your hard drive is damaged.
If you have any important data on hte drive you should attempt to recover it first before you do anything that will damage whats left of the data.
As far as reformating, I wouldn't trust the disk anymore until I had recoverd the data, reformated the disk and tested the disk with either the onboard diagnostics (brand name computer) or the Hard Drive Manufacturers Diagnostics Utility.
If you don't test the drive properly before formatting and re-installing, you are probably just wasting your time.
If the drive is bad this is just going to keep happening.
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending