Question Locked

black screen no boot

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Have HP Pavilion laptop, when you press power all led lights come on, tries to boot cd runs momentarily no noise coming from hard drive though it runs mementarioly. Have took out memory it beeped and put back, any ideas. it is runnig vista and just ot of warranty (1 year old)

13 replies

by darryl~

Did anything happen to cause it to start doing this?
Have you tried to boot from your Vista CD?

Edited for:
Did you remove the battery & reinsert it?

by fregeus

..booting from the CD (Windows Vista CD) and tried a repair or tried to access your hard drive?

It sounds to me like your HD may be busted.

TCB

by tommyd123

I think if the hard drive was shot I would still be able to get into bios.

by brian

It could be the main board...i have seen a few HP's do this, but make sure that it is not the screen, you can try hooking it up to a external monitor to check. Also, test the power adapter to make sure it has the proper voltages being supplied to the system.

by balge

hi
you could try a bootable CD, if you haven't got system CD - see if its the HDD or motherboard
Need any help with that post back
cheers

by jgirizarry

I would remove the HDD and plug it into a HDD usb adapter on another PC, then try to write or read from it to see if its working.

by older mycroft

I've had this situation when the external monitor has been removed without adjusting the monitor priority - and the Boot Password still wants to appear on the non-existent monitor. ;)

If you [b]DO[/b] have a Boot Password, just go ahead and type it in (as you would if you saw the Password Box onscreen) then when the OS boots, it'll appear on this 'secondary' monitor. :)

[i]That's my only idea.[/i]

by chris029

It sounds like the Power Supply is failing, but you must also consider the Power Switch and the motherboard. If the Power Supply is failing it can just shut down, or be confused by signals it receives down the orange startup wire. Powerswitch is also a good candidate for problems as it has moving parts in it that can be worn after time. It is usually very propietary Powersupply so getting one to test might be tricky depending on the model. I would check the Power switch with an ohm meter to make sure it is a momentary 'on' and not giving any other signal. Reset switch if there is one I would check it also. Usually this sounds like the Power Supply that would be my first item to troubleshoot. Any power glitches lately?

by rob miners

You could give the inside of the case a blowout with compressed air. When blowing air through the fans make sure that you physically stop them from spinning, as they may generate power and cause damage.

Next, remove the Heatsink, give it and the CPU top a thorough clean with a cotton cloth and reseat the CPU applying new CPU grease. Arctic is a good brand.

If the Fans spin freely when you give them a spin they are probably OK. If there is resistance replace them.

Clean the Cooling Vents

Depending on the model, vents can be found on the side, back, and/or bottom of the notebook PC. These vents allow air to flow through the PC and keep it cool. Buildup inside these vents impedes the cooling process.

Clean I/O Ports

The back of the notebook PC has a series of ports. After cleaning the cooling vents, take the compressed air and blow out any debris that may have accumulated in and around these ports.

Clean the RAM

Clean the golden edge of each memory stick with a soft rubber/eraser, remembering not to touch the golden edge of the memory stick. Check with one stick at a time, remembering to disconnect the power from the PC.

One way to help in this situation to help cool the unit is to use a Notebook Cooling Chill Mat, something like this.

http://www.ao3.com.au/product.asp?manufpartno=AWE11US

http://lonewolf-online.net/computers/tutorials/dismantle-clean-hp-laptop/

This discussion is closed to new replies.