Discussion Locked

Board Not Responding On New Build

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Just put this PC together.
Intel D875PBZ board and P4 2.8E processor
2X 512 megs of PC3200 dual channel Corsair
60 gig SATA hard drive
8X AGP graphics card
Problem:
push the start button on the case and everything lights up, fans start, keyboard lights up, heatsink fan begins to run, but for less than a second.
It will do this every time that you push the start button.
All jumpers have been double checked as well as case connections.
There doesn't seem to be a short between the board and the case.
What could be the problem?

17 replies

by wcp

This is most likely a heat issue.

Make sure the heatsink unit was installed correctly. The heatsink may not be touching the CPU fully. Also make sure a thermal paste was applied.

If this does not resolve the problem, it?s got to be either motherboard or memory. Use one RAM only and see if this corrects the problem. Otherwise, it is the motherboard.

by wcp

This is most likely a heat issue.

Make sure the heatsink unit was installed correctly. The heatsink may not be touching the CPU fully. Also make sure a thermal paste was applied.

If this does not resolve the problem, it?s got to be either motherboard or memory. Use one RAM only and see if this corrects the problem. Otherwise, it is the motherboard.

by birdmanmar3

"There doesn't seem to be a short between the board and the case" And you determined this how? Did you take the board out of the case? I know it is a pain but to rule out this possibility, that needs to be done. On more than one occasion I have glued the little brown cardboard washers on the mobo mounting studs (standoffs) even then one board was fine until I tightened the mounting screws. Once again it would short out. I had a MSI board not to long ago that was acting the same way as yours. This board, as it turns out,was a combination of the PS & and the type of ram I was using. Short time to fix this boards requirement but an extended time to ascertain what was needed. Good Luck

by birdmanmar3

"There doesn't seem to be a short between the board and the case" And you determined this how? Did you take the board out of the case? I know it is a pain but to rule out this possibility, that needs to be done. On more than one occasion I have glued the little brown cardboard washers on the mobo mounting studs (standoffs) even then one board was fine until I tightened the mounting screws. Once again it would short out. I had a MSI board not to long ago that was acting the same way as yours. This board, as it turns out,was a combination of the PS & and the type of ram I was using. Short time to fix this boards requirement but an extended time to ascertain what was needed. Good Luck

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by bob

It's one of those X90 heat sinks and it was quite a process to get it in place. Pretty sure it is in properly and has enough thermal compound. I don't see it overheating in a matter of less than a second. Is this really possible?
I did take the board out and check it. I even touched a little elmers to the standoffs so that the fiber washers would stay in place when I put the board back.

by josh

Check your PSU for bad voltatge, make sure you have your P4 plugged into the board.
Try booting with a different PSU with a higher wattage.

by ozi eagle

Hi,

Check your electro caps around the CPU. This fault is typical of faulty caps. See articles under discussions / miscellaneous.

by aquadag1

Your board might be of older revision and doesn't support Prescott processors. Same happened to me when i tried to upgrade my system with another processor, using d875pbz. Have 2.4c, tried 2.8e. Check intel website.

This discussion is closed to new replies.