Question Locked

Can someone tell me how to take out my old CPU?

0 helpful
22 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a Dell Dimension 2400 with a Pentium 4 2.2GHz processor. I have found a 3.06 GHz /533 MHz Pentium 4. Is it going to be easy for me to do this myself? Thank you for any info.

22 replies

by jfuller05

know what the socket is? A processor connects to the motherboard by way of a socket.

by patb071

Have you made sure that the cpu is compatible with the motherboard? also you will need some thermal grease to apply the heat sink to the cpu

by lilac22281

to make sure that this one would be compatible. I was disappointed to know that I could only upgrade this machine to another Pentium 4.
I have never heard of thermal grease--thanks for the info and help.

by jfuller05

Examine the new Pentium 4 processor and verify that all the pins are straight and ready to be plugged into the motherboard. If any of the pins are bent, carefully push the pins back into place by hand.
Shut the computer off and unplug the electrical cord on the back of the computer base from the power source. Then undo the screws on the back of the central processor unit (CPU) with a screwdriver and slide the case top off of the base. Lay the case down so that the motherboard is lying flat, even with the table surface that you are using.
Locate the Pentium processor that is in the motherboard. Remove the old processor by lifting the socket handle on the side of the processor until it is vertical to the motherboard and lifting the processor straight up until it is clear of the pin sockets and then take the processor out of the CPU. Do not lean on any parts connected to the motherboard while lifting the processor out.
Turn the new Pentium 4 processor over so that you are looking at the pin side and locate the triangle in the corner of the processor. You will use this corner as your orientation point. Line up the corner with the marking on the processor sockets on your motherboard. When you have the new processor in position, push down slowly and carefully to prevent any pins from getting bent or damaged.
Press the center of the processor and each of the corners to verify that it is seated properly in the motherboard. Close the lever on the side of the processor to lock it into the motherboard.
Slide the cover back over the computer base and secure the cover with screws. Plug the electrical cord from the computer back into the power source and turn the computer on to verify the processor is working properly. When you are satisfied, turn the computer off.

by lilac22281

Thank you also. I probably could have found that on Dell, but I have 4 kids and no patience. Sometimes I feel like I have adult A.D.D.!

by willcomp

Exercise caution when removing heat sink retaining clips. They are plastic and become a bit brittle with age.

CPU is supported by motherboard but you may need to update BIOS before removing old CPU. You have an older Dimension 2400 and BIOS likely does not include support for a 3GHz CPU.

by lilac22281

I know there is an update, but I heard that flashing the BIOS requires great caution. Oh, and I have to have a floppy drive to flash my BIOS, according to the Dell website. Thanks for the heatsink clips info.

by oh smeg

The 2.2 P4's had a FSB of 400 MHZ and if your replacement CPU has a FSB of 533 you'll need to confirm that first the M'Board will work at this frequency.

If it doesn't support this CPU then no matter what you do the system will not work.

Col

by willcomp

Mobo supports 3.06GHz P4s with 533MHz FSB. I verified prior to posting comment above.

by lilac22281

but I confirmed it on the Dell website. That's where that person got their info about the compatible mobo. Thanks

by oh smeg

Opening the case changing any Jumpers on the M'Board that may need changing and removing the CPU Heatsink. On one side of the CPU is a Lever that you push down prize away from the socket slightly and allow to lift up. With the lever up lift the CPU out of the socket.

Grab the replacement CPU and align it to the socket so that it drops in [i]there is only one way that this goes into the socket here[/i] and then press the Lever back into the Lock Position wipe the Top[i]Metal Pert of the CPU[/i] with a Alcohol Wipe to clean it and the Part of the Heat Sink that Contacts the CPU apply a thin layer of Thermal Compound [b]Silicon Grease[/b] though be extremely careful here not to actually touch the Thermal Compound with your skin as it will contaminate it. Use a Cleaned Screwdriver to spread the paste over the CPU and then refit the Heatsink.

The P4 CPU's had 3 Generic Heat Sink Fitting Types and then places like Dell had their own methods of fitting these so you need to proceed carefully and never force anything.

Be Gentle but firm and if required use a small Flat Balded Screwdriver to help remove the Locking Legs of the Heat Sink. After you have the replacement CPU fitted and the heat sink on start the computer and enter the BIOS and check that the CPU is correctly Identified. Save the changes as you exit the BIOS and your all set. ;)

Col

by lilac22281

All of you have given me free info to help me that The Geek Squad probably would have charged me $300 for. I really do appreciate all of your help!

by lilac22281

i didnt look at each individual answer, so i didn't see thumbs up. thanks--i gave you one too

by cg it

thumbs are a way to say thanks to those here who provide suggestions that help you solve a problem or at the least steer you to a resource.

by lilac22281

you helped me with giving recognition to those who deserve it!

This discussion is closed to new replies.