Question Locked

cannot boot from cloned sata

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I cannot get my new sata drive (cloned from ata) to boot.
Background: I added a WD Caviar 500gig sata HD to my ASUS P4S800 MB (no sata support), so use a new Promise TX2300 pci/sata card to run it. I have existing two ata drives 1st is WD120gig w/3 partitions 1.WinXP pro, 2. data drive, 3. Vista Home Premium. 2nd drive is WD80gig w/2 partitons 1. data, 2. data. I dual boot Vista and WinXP pro. The new WD500gig HD installed and formatted w/o incident. I then used Acronis 10 to clone my WD 120gig drive into new WD 500gig drive. That completed with no errors. I then unplugged the cloned drive and booted. Promise driver asks which drive to boot from, I select the new WD500gig drive, then Vista dual boot menu asks which opsys to boot, I select Vista, and then I get error that winload.exe is not present in windows directory. It informs me I have to repair windows with windows DVD and restart. But, doing such does not come back to this point. I expect a clone to be exact duplicate, (in past when cloning an ata to an ata, the new clone ata drive just booted and no other issues, but here the sata is mnot. Any ideas for resolving this? thanks

6 replies

by langlier

is that when you cloned the drive over you didnt get the proper SATA drivers installed. A clone may not work in this case because of this fact.

by hal 9000

But you are attempting to get the Computer to work in a different manner by booting from a SATA Drive connected through a Plug In PCI Card so those PCI SATA Drivers are not present in the Boot Setup.

If you where cloning from an IDE to IDE drive it would work perfectly and if you where doing the same thing from a SATA to SATA drive you wouldn't have any problems as you would have already added the necessary PCI to SATA Driver. You could even clone from a SATA to IDE and have it work but you [b]Can Not[/b] Clone from an IDE to SATA and have it work as the SATA drivers are not present in the Boot Up sequence.

Then just to add another twist if you where to replace th IDE Drive that will be the default drive and the computer will always attempt to boot from that drive so if you where to do a Repair Install of both XP & Vista you would need the IDE Drive in place to allow some low level boot files to be copied to it so that the computer could be pointed to the correct drive to boot from.

Your only solution here is to setup the computer the way that you plan on using it permanently and then do a Repair Install of both OS's so that you can get the correct boot drivers installed. You'll also need a Floppy with the PCI to SATA Drivers copied directly the the root of the floppy as when you install any Windows System you need to allow the Windows Installer access to the Install files.

Once you have one OS working properly you can install the other so I would suggest that you repair the XP install by following the directions here

http://tinyurl.com/g4bv8

Then at the first blue screen press the [b]F6[/b] key and wait till you are asked to install the driver for the PCI top SATA Card and then allow the system to load as per normal. Once you have XP working you should be able to do a repair install of Vista without any problems or the need to add the PCI to SATA Drivers.

Col

by jdphelps50

HAL 9000, Thanks for good explanation, sounds reasonable, and I will try it, but, I am confused why would the prompt by Promise (brand of pci/sata card) for me to select the drive to boot from (this happens before Vista's dual boot prompt), because of this, it seems like the sata card is already configured and drivers present, (after all I did use the drive to clone my ata) Are boot drivers different than just regular drivers, if there is such a thing? Needless to say, I am not familiar with boot stuff, and the things (winXP, or Vista) do to cause bootable partitions, so I will try your suggestion. Note: I installed this controller card and HD using Vista and stuff downloaded from Promise website. It was simple to get everything running for a MB w/o sata support and using this addon controller card.... thanks

by ugadata

The prompt you see is most likely from the BOIS in the the Promise SATA add-on card.

by hal 9000

For want of a better word as these Plug In Cards have their own Firmware and can be SATA, SCSI. RAID all will give the same option but because of the order that the drivers have been loaded they will not necessarily be in a position to load those drivers to boot from. This isn't OS Dependant but Hardware Dependant and will affect any OS that is used when something like this is done.

While some different OS's may be able to pickup new hardware and deal with it most can not and you need to do a repair install to get the system to work in the different configuration.

Col

This discussion is closed to new replies.