Can't Defrag
I'm running a computer with Win 98 Sec. Ed. when I go to defrag the system, I keep getting a loop between 0% and 3%? Any ideas? The only thing that has changed on the system is that I am now using Road Runner (DSL) as the ISP.
Jim
Desktop
I'm running a computer with Win 98 Sec. Ed. when I go to defrag the system, I keep getting a loop between 0% and 3%? Any ideas? The only thing that has changed on the system is that I am now using Road Runner (DSL) as the ISP.
Jim
by pfenness
by jzeman
by stngfan1
A program is writing to the harddisk. You can boot up in safe mode, then run defrag. You can find the offending program, with Ctrl, Alt, Delete, and end task one at a time to see if you can find the offendor.
Check your startup group do you have too many or any unnecessary programs running.
How many items in your system tray, try to remove any you really don't need.
TM
by jzeman
by pschuvie
The easiest and most straight forward thing to do when you want to run Defrag is to reboot to safe mode. Start>Shutdown>reboot,
hold down the ctrl key just at the starting Windows or Windows splash screen appears. Select Safe mode.
This eliminates all the unneeded items of a normal booting and give you a clean memory setup to work with.
The addition of the cable modem is probably the program that is working in the background. Since it is an "always on" connection there is some pollinghappening that wants to make sure your there and communicating. So the safe mode eliminates this connection for the period of your defragging.
It sounds like you have done this often before and therefore the only other thing to check is the "Settings" of deframenter. Sometimes the button for "rearrange files" gets checked, by someone else looking around, and this can really cause the defrag to run back and forth sorting things out. If you defrag regularly the rearrangement is not, in my opinion, needed.
Hope this helps.
by jzeman
by pjpatiky
All running programs should have End Task or Disable applied to avoid interference with Scan-Clean-Defrag. To do this:
Put screen to Desktop. Press Ctrl+Alt keys and tap Delete key once. (C-A-D). A Close box opens. Highlight program, then click the End Task button. Explorer and Systray are to remain untouched. Close box will disappear. Now C-A-D again, highlighting next program, and click End Task. At times a program will require clicking End Task twice, or a second box appears with an End Task button that you click on. After Ending all programs, except Explorer and Systray, go to your System Tray (lower right, by clock) and click on any Icons to Disable or close their features. Then, on Desktop right click open space>properties>Screen Saver tab, place Screen Saver on none, click Apply /OK. On same tab click Settings button for Power Mgt and place settings on Always on, Never, Never, Never, click Apply/OK. Do S-C-D. Reboot and reset Screen Saver and Power Mgt.
See http://support.microsoft.com/support/kb/articles/Q222/4/69.asp
There is a Program called Enditall that aids the Ending of most of your Programs. See www.zdnet.com. In Zdnet?s search box, type in Enditall (one word).
Another method is Start>Run, type msconfig , click OK. In System Config. Utility box dot Selective Startup. Uncheck all items listed under Selective Startup. Grayed-out items are empty or missing. Click Apply/OK. Now Reboot. Windows will start with only basics running. Disable Systray Icons. After Reboot run S-C-D. When S-C-D is complete go back to SCUbox and dot Normal startup and reboot. Reset Screen saver and Power Mgt.
Or, from the menu choose Safe Mode. Then run S-C-D. When complete Reboot, set Screen Saver and Power Mgt. Some WN98?s require holding Ctrl key during startup.
For WNMe the same End Task/Disable navigation applies prior to S-C-D
by jzeman
by netfuzzy
Defrag may not complete for two major resons:
1. An application or a task is attempting to write to the hard disk: To take care of this disable all background applications including an antivirus or anyother gaurd installed, Also make sure the screen saver is disabled. Rebooting into safe mode is a good idea as it will take care of the device conflicts or faulty device drivers which attempt to communicate with the processor interiptting the Defrag.
2. Another possibility is the Corrupt Hard Disk Media or Faulty Windows Core file: Booting using a Startup Disk, and perform a through ScanDisk through the COMMAND prompt, and them run Defrag. If this works, then boot in Windows and run Defrag. If Defrag fails in Windows only then I suggest you Reload Windows. If the Defrag fails in DOS, generally it corresporonds media errors. Try FDISK and the FORMAT and Reload the operating System.
by toltec58
Hi Jim,
As the other answers have said you CAN do a ctl-alt-del to turn off the offending program or boot to safe mode and defrag. But, if you're like me (lazy), you setup defrag and scandisk to run in task scheduler while you're away from your PC.
You have a TSR (terminate and stay resident) program running in the background. The problem you are having happened to me after I downloaded Winamp. Did you recently load some new software and was defrag working before?
Here's waht you do..
Click start/ Run type msconfig
Click the Startup Tab and uncheck the TSR that is running in the background.
Defrag will work now :-)
T58
by jzeman
This discussion is closed to new replies.
Sort by Trending