These are just a few examples of beep codes to some motherboards, yours maybe different so check your board makers website and download their manual(s) to your make of board.
AMI BIOS beep codes:
Beep Code Descriptions
1 short -- DRAM refresh failure
2 short -- Parity circuit failure (This code usually means a problem with either the system memory or the motherboard)
3 short -- Base 64K RAM failure
4 short -- System timer failure
5 short -- Process failure
6 short -- Keyboard controller Gate A20 error
7 short -- Virtual mode exception error
8 short -- Display memory Read/Write test failure
9 short -- ROM BIOS checksum failure
10 short -- CMOS shutdown Read/Write error
11 short -- Cache Memory error
1 long, 3 short -- Conventional/Extended memory failure
1 long, 8 short -- Display/Retrace test failed
AWARD BIOS beep codes:
Beep Code Description
1 long, 2 short --
Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information
Any other beep(s) -- RAM problem.
IBM BIOS beep codes:
Beep Code Description
No Beeps No Power, -- Loose Card, or Short.
1 Short Beep -- Normal POST, computer is ok.
2 Short Beep -- POST error, review screen for error code.
Continuous Beep -- No Power, Loose Card, or Short.
Repeating Short Beep -- No Power, Loose Card, or Short.
One Long and one Short Beep -- Motherboard issue.
One Long and Two Short Beeps: --
Video (Mono/CGA Display Circuitry) issue.
One Long and Three Short Beeps. --
Video (EGA) Display Circuitry.
Three Long Beeps -- Keyboard or Keyboard card error.
One Beep, Blank or Incorrect Display --
Video Display Circuitry.
Macintosh startup tones
Tones Error
Error Tone.
(two sets of different tones) -- Problem with logic board or SCSI bus.
Startup tone, drive spins, no video --
Problem with video controller.
Powers on, no tone. -- Logic board problem.
High Tone, four higher tones. -- Problem with SIMM.
Phoenix BIOS beep codes
Beep Code Description and what to check
1-1-1-3 -- Verify Real Mode.
1-1-2-1 -- Get CPU type.
1-1-2-3 -- Initialize system hardware.
1-1-3-1 -- Initialize chipset registers with initial POST values.
1-1-3-2 -- Set in POST flag.
1-1-3-3 -- Initialize CPU registers.
1-1-4-1 -- Initialize cache to initial POST values.
1-1-4-3 -- Initialize I/O.
1-2-1-1 -- Initialize Power Management.
1-2-1-2 -- Load alternate registers with initial POST values.
1-2-1-3 -- Jump to UserPatch0.
1-2-2-1 -- Initialize keyboard controller.
1-2-2-3 -- BIOS ROM checksum.
1-2-3-1 -- 8254 timer initialization.
1-2-3-3 -- 8237 DMA controller initialization.
1-2-4-1 -- Reset Programmable Interrupt Controller.
1-3-1-1 -- Test DRAM refresh.
1-3-1-3 -- Test 8742 Keyboard Controller.
1-3-2-1 -- Set ES segment to register to 4 GB.
1-3-3-1 -- 28 Autosize DRAM.
1-3-3-3 -- Clear 512K base RAM.
1-3-4-1 -- Test 512 base address lines.
1-3-4-3 -- Test 512K base memory.
1-4-1-3 -- Test CPU bus-clock frequency.
1-4-2-4 -- Reinitialize the chipset.
1-4-3-1 -- Shadow system BIOS ROM.
1-4-3-2 -- Reinitialize the cache.
1-4-3-3 -- Autosize cache.
1-4-4-1 -- Configure advanced chipset registers.
1-4-4-2 -- Load alternate registers with CMOS values.
2-1-1-1 -- Set Initial CPU speed.
2-1-1-3 -- Initialize interrupt vectors.
2-1-2-1 -- Initialize BIOS interrupts.
2-1-2-3 -- Check ROM copyright notice.
2-1-2-4 -- Initialize manager for PCI Options ROMs.
2-1-3-1 -- Check video configuration against CMOS.
2-1-3-2 -- Initialize PCI bus and devices.
2-1-3-3 -- Initialize all video adapters in system.
2-1-4-1 -- Shadow video BIOS ROM.
2-1-4-3 -- Display copyright notice.
2-2-1-1 -- Display CPU type and speed.
2-2-1-3 -- Test keyboard.
2-2-2-1 -- Set key click if enabled.
2-2-2-3 -- 56 Enable keyboard.
2-2-3-1 -- Test for unexpected interrupts.
2-2-3-3 -- Display prompt Press F2 to enter SETUP.
2-2-4-1 -- Test RAM between 512 and 640k.
2-3-1-1 -- Test expanded memory.
2-3-1-3 -- Test extended memory address lines.
2-3-2-1 -- Jump to UserPatch1.
2-3-2-3 -- Configure advanced cache registers.
2-3-3-1 -- Enable external and CPU caches.
2-3-3-3 -- Display external cache size.
2-3-4-1 -- Display shadow message.
2-3-4-3 -- Display non-disposable segments.
2-4-1-1 -- Display error messages.
2-4-1-3 -- Check for configuration errors.
2-4-2-1 -- Test real-time clock.
2-4-2-3 -- Check for keyboard errors
2-4-4-1 -- Set up hardware interrupts vectors.
2-4-4-3 -- Test coprocessor if present.
3-1-1-1 -- Disable onboard I/O ports.
3-1-1-3 -- Detect and install external RS232 ports.
3-1-2-1 -- Detect and install external parallel ports.
3-1-2-3 -- Re-initialize onboard I/O ports.
3-1-3-1 -- Initialize BIOS Data Area.
3-1-3-3 -- Initialize Extended BIOS Data Area.
3-1-4-1 -- Initialize floppy controller.
3-2-1-1 -- Initialize hard-disk controller.
3-2-1-2 -- Initialize local-bus hard-disk controller.
3-2-1-3 -- Jump to UserPatch2.
3-2-2-1 -- Disable A20 address line.
3-2-2-3 -- Clear huge ES segment register.
3-2-3-1 -- Search for option ROMs.
3-2-3-3 -- Shadow option ROMs.
3-2-4-1 -- Set up Power Management.
3-2-4-3 -- Enable hardware interrupts.
3-3-1-1 -- Set time of day.
3-3-1-3 -- Check key lock.
3-3-3-1 -- Erase F2 prompt.
3-3-3-3 -- Scan for F2 key stroke.
3-3-4-1 -- Enter SETUP.
3-3-4-3 -- Clear in-POST flag.
3-4-1-1 -- Check for errors
3-4-1-3 -- POST done--prepare to boot operating system.
3-4-2-1 -- One beep.
3-4-2-3 -- Check password (optional).
3-4-3-1 -- Clear global descriptor table.
3-4-4-1 -- Clear parity checkers.
3-4-4-3 -- Clear screen (optional).
3-4-4-4 -- Check virus and backup reminders.
4-1-1-1 -- Try to boot with INT 19.
4-2-1-1 -- Interrupt handler error.
4-2-1-3 -- Unknown interrupt error.
4-2-2-1 -- Pending interrupt error.
4-2-2-3 -- Initialize option ROM error.
4-2-3-1 -- Shutdown error.
4-2-3-3 -- Extended Block Move.
4-2-4-1 -- Shutdown 10 error.
4-3-1-3 -- Initialize the chipset.
4-3-1-4 -- Initialize refresh counter.
4-3-2-1 -- Check for Forced Flash.
4-3-2-2 -- Check HW status of ROM.
4-3-2-3 -- BIOS ROM is OK.
4-3-2-4 -- Do a complete RAM test.
4-3-3-1 -- Do OEM initialization.
4-3-3-2 -- Initialize interrupt controller.
4-3-3-3 -- Read in bootstrap code.
4-3-3-4 -- Initialize all vectors.
4-3-4-1 -- Boot the Flash program.
4-3-4-2 -- Initialize the boot device.
4-3-4-3 -- Boot code was read OK.