Question Locked

Computer won't boot from hard drive after windows formats a partition

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Just bought a brand new seagate 320GB hard drive, and popped in the dell xp restoration cd

never had a problem like this before with the disk, so i've figured its the hard drive

after windows formats the new partition, it reboots, like it normally should.

and instead of booting off the hdd like it then should, it continues to try to boot off the cdrom, even if i change the order in the BIOS

i'm guessing the BIOS isn't recognizing my hdd, even though windows can see the partition clearly

help?
Andrew

11 replies

by ghostbrowser

Windows XP has a problem with LBA 48
That is hard drives bigger than 134 Gigabytes
So you need to make a partition under this barrier for windows xp to boot from
Windows xp sp2 does not have this problem
What size is it in your bios setup

by avechinski

my bios doesn't seem to show what's plugged into the SATA drives. i'm running a gigabyte k8 triton board

also, i did try to install XP home edition.
it did create a partition less than 134GB, but i still ran into the boot error

i'm fairly certain its not the hard drive, since the indicator light shows that its operating fine...its just that my computer, or rather, bios, doesn't want to boot from anything other than the cd drive

i've set the boot order to hard drive on first priority, everything else disabled

bios runs, checks the system, then displays "boot from cd:"

by ozi eagle

Hi,
When youoaded XP did you press F6 when asked and load the SATA drivers?

This could explain why the drive is not recognized.

Herb

by ghostbrowser

Turn on auto detect for each possible drive
You may need to boot from hard drive 1 or 2 or 3 etc set up your sata to be ide 0
Is sata an add on card = pci ?
or if its raid try scsi or add on bios
Main thing is windows can see it
It just needs to boot
Try unpluging all other drives cd floppy etc
Check all the bios settings look at all pages look for all the choices
If you have a book for the main/mother board
This may also help somebody else who reads it that is why I have given you so much info in the most simple terms

Hope this helps

by avechinski

oddly enough by entering my RAID setup (only one hdd is in my system, haven't put in the 2nd one yet) and making the "free disk" an array, my computer detected the hard drive and everything is dandy now

also, does anyone know what the jumper settings are to set a samsung drive to slave?

by ghostbrowser

Ide drives have 3 settings
Master = MA
Slave = SL
Cable Select = CS

Cable select is good if you have the right cable
The master connects to the end (Black)
The slave connects to the Middle (Gray)
The other or long end to the main board (Red or Blue those are the ones I have seen)
Means you don't have to get at the jumpers
Just plug in the right connector
If you only have one drive on the cable it must go on the end don't use the middle one
On the samsung drive I have
Second from the power connetor is CS
No jumper on for SL
First from the data connector is MA
Looking from the back label top power right
4 jumpers from left to right
1st MS
2nd Limit Capacity to 32GB
3rd CS
4th ????
Don't put a jumper on MS and CS at the same time just move it or leave it off

Hope this helps
Ps this is stevemrm
Just got me a handle
What do you think ok or dumb?
Picture is next

by avechinski

both drives are SATA, so i'm sue that changes things

I want the master to be the 320 seagate I just got, and the other the 160 samsung I already had

put the seagate in SATA-1 and the samsung in SATA-2?, i've looked around for jumper settings and I really haven't gotten a clear answer

by aijayes

I had the exact same problem, with a Gigabyte 8IK1100 (Titan P4). Enabling RAID and SATA didn't solve the problem, but when I did that, the second page of BIOS setup gave me the option to change hard drive boot priority.
It was wrong! I changed it to my new drive and now everything works GREAT! Thanks for the ideas!

by ghostbrowser

Sata don't have masters or slaves
But most sata controllers make it look like
They are ide drives
So try swapping the plugs on the drives
If you have two sata ports they can be master and slave
So plug a drive into each port and see what happens
But some controllers (sata 1) can not see Sata drives the drives just need to be slowed down and there is a jumper for that on some/most? drives

Cheers

by ghostbrowser

Sata don't have masters or slaves
But most sata controllers make it look like
They are ide drives
So try swapping the plugs on the drives
If you have two sata ports they can be master and slave
So plug a drive into each port and see what happens
But some controllers (sata 1) can not see Sata 2/300 drives the drives just need to be slowed down and there is a jumper for that on some/most? drives

Cheers

This discussion is closed to new replies.