Question Locked

Dell Dimension 4600 and BSOD

0 helpful
23 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm running a Dimension 4600 that gets a blue screen witn a stop code 0x0000007B (0xf7996528, 0xc0000034, ox00000000,0x00000000), no other information other than to check my hard drive etc. Can't even boot to Safe Mode. I have run all of Dell diagnostics and do not get any errors (ran for hours, all tests, all devices).
I have checked everything (memory, pci cards, cpu, etc), nothing. I have used up to four different hard drives, and they all get the same BSOD. I know these drives are good, I can boot from them on another PC and get to the Windows XP desktop. I changed the IDE cable to the HD, nothing. I also upgraded BIOS. Since I got the same BSOD, I figure maybe the Power Supply is shot, so I replaced PSU. However, same BSOD.

I'm at a loss right now. Spke to Dell rep and he said that I need to reinstall XP with Dell's reinstallation disk, which is directly tied to the motherboard. When I tried to reinstall XP and got to the screen where you hit start the install of XP, the keyboard does not work. I have tried multiple keybaords and they all work in DOS, so I'm blown out by this. I finally took the new HD and installed in another computer, installed Dell XP software disk, made sure the PC booted and was operational at the desktop level, transferred to the Dell Dimension 4600 and bam, BSOD. Also got my hands on another 4600 which I know works and the BSOD appears when I use the newly formatted HD. I know this is a long post, but any ideas?

PS The Dimension 4600 ABCD status lights are all green.

23 replies

by ebayva

Have you checked the motherboard for blown or bulging caps? And have you tried removing the CMOS battery to completely reset the system?

Also, did the other 4600 still work with a hard drive that was not previously in the crashing machine?

by morenito44

Thanks for the reply. The capacitors look fine and not swollen. I removed the CMOS battery and the auto ide configuration occurs and I reset the day and time, still BSOD. I should correct myself, the second 4600 came without a hard drive and no matter which of the four hard drives I use, the BSOD. I even obtained the same type of HD that the first 4600 came with just to be sure. Tried to holdd power button for 30 seconds, remove password jumper,nothing. There must be something unique about these 4600's, but I cannot find it.

by morenito44

Thanks, but my BSOD does not say unmountable boot device. There is no technical info other than the 0x..7b message. I went thru Microsoft's tech info and none of the posts there applied to my situation.

by morenito44

Thanks, but my BSOD does not say inaccessable boot device. There is no technical info other than the 0x..7b message. I went thru Microsoft's tech info and none of the posts there applied to my situation.

by morenito44

I can boot off a floppy to get to c drive. How do you get to a minidumps?

by rob miners

if you set it as a Slave and connect it to a System or you can use a bootable Linux CD.

http://www.pclinuxos.com/index.php?option=com_ionfiles&Itemid=28

Minidump Files can be found here. C:\WINDOWS\Minidump\Mini122707-02.dmp

How to read the small memory dump files that Windows creates for debugging

http://support.microsoft.com/kb/315263

To download and install the Windows debugging tools, visit the following Microsoft Web site:

http://www.microsoft.com/whdc/devtools/debugging/default.mspx

Instructions on using Windbg.

Open Windbg and select file, Symbol file path and browse to the Symbol folder that you have downloaded and installed Symbols to, select OK.
Close the workpage and save the Workspace information. This should lock in the Symbol path.
Open Windbg and select file and select Open Crash Dump then navigate to the minidump, highlight it and select Open.
There are two ways to use !analyze -v the easiest is to click on !analyze -v under Bugcheck Analysis.
When you have ran the initial dump if you look to the bottom of the screen you will see kd> to the right of that type in !analyze -v and press the Enter key.
Ctrl + a will let you copy the information and paste it into notepad.

Look to the bottom of the page for information like this. This was fixed by updating the Graphics Drivers.
FAULTING_THREAD: 864f6a98

DEFAULT_BUCKET_ID: GRAPHICS_DRIVER_FAULT

CUSTOMER_CRASH_COUNT: 1

BUGCHECK_STR: 0xEA

PROCESS_NAME: logon.scr

LAST_CONTROL_TRANSFER: from 00000000 to bfef0fea

STACK_TEXT:
f6434e6c 00000000 00000000 00000000 00000000 sgiul50!DrvBitBlt+0x585

STACK_COMMAND: .thread 0xffffffff864f6a98 ; kb

FOLLOWUP_IP:
sgiul50!DrvBitBlt+585
bfef0fea 75f9 jne sgiul50!DrvBitBlt+0x580 (bfef0fe5)

SYMBOL_STACK_INDEX: 0

SYMBOL_NAME: sgiul50!DrvBitBlt+585

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: sgiul50

IMAGE_NAME: sgiul50.dll

DEBUG_FLR_IMAGE_TIMESTAMP: 3b7dfec7

FAILURE_BUCKET_ID: 0xEA_IMAGE_sgiul50.dll_DATE_2001_08_18

BUCKET_ID: 0xEA_IMAGE_sgiul50.dll_DATE_2001_08_18

by morenito44

Wow, lots to tke in. This could be a dum question, but when I boot to the c prompt and type DIR, should I not see a windows directory (winnt something other than the normal system files?). Is this becus i formatted in NTFS?

by rob miners

CD and CHDIR
Use the cd and chdir commands to change to a different folder. For example, you can use the following commands:
Type cd .. to change to the parent folder.
Type cd drive: to display the current folder in the specified drive.
Type cd without parameters to display the current drive and folder.
The chdir command treats spaces as delimiters. Because of this, you must put quotation marks ("") around a folder name that contains a space. The following is an example:
cd "\windows\profiles\username\programs\start menu"
The chdir command works only in the system folders of the current installation of Windows, in removable media, in the root folder of any hard disk partition, or in the local installation sources.

http://support.microsoft.com/kb/305595

http://support.microsoft.com/kb/314058

by samhobbs

Have you used the system before, with a different drive or with the hard drive formatted with something else?

I think that model of Dell uses an AGP adapter. Are you using the same AGP adapter that was in the sytem? If not then perhaps the adapter is incompatible.

Are you able to boot from a CD-ROM?

by morenito44

This system has been in use since 2004, but with its original drive. The original hard drive is dead. I purchased the same type of HD that went bad. I obtained (from Dell) the original XP OS. I could not install the XP on the new drive on the 4600 becuz the keyboard does not work in the XP install mode (don't know why), so I installed the XP OS on a VAIO desktop. The install went without a problem and I was able to use the reinstalled HD on the VAIO. But when transferred to the 4600, I don't make it to the Windows XP splash screen. Yes, I tried using the original AGP card and a second AGP from another 4600 and still BSOD. If I remove the AGP card, then how will I see what's happening?

by ebayva

First, usually when you install XP on one model system, it will only be compatible with the same model you installed on, which could explain why the drive you took from the VAIO did not work in the 4600. Also, some machines don't like a USB keyboard until they have XP on them. Have you tried using an older keyboard with a PS/2 connector?

by samhobbs

I thought you had used a different system to install Windows onto the drive. I think that Windows uses it's own version of the BIOS, which is system-dependent. If so the the VAIO BIOS won't work in a Dell. Someone in an earlier reply I think provided a link to instructions for installing for a system different from the system used to do an install; perhaps you need to do that.

When you say "If I remove the AGP card, then how will I see what's happening?" you are being too quick to criticize. I did not suggest not using an AGP card. Don't be so quick to criticize.

by santosh_arasu

Try to remove all the PCI cards or if u have VIdeo cards such as NVIDIA or AGP try removing it and try to start a installation.Disable the NIC and integrated audio and try itJust One more qusetion! did u try changing the Hdd setting to Raid Auto Detect/ATA in BIOS before starting the installation

by santosh_arasu

As said a USB keyboard may not work some times try using a PS2 keyboard for the Xp installatio that will definetly work

by morenito44

I am using a PS2 keyboard on the 4600. I actually tried 3 PS2 keyboards and they all work in in DOS, but not in the Windows setup. I started in DOS with a blank HD, then tried to install XP from the cd, but as I said, it won;t accept the enter command, PF3, nothing.

by samhobbs

An installation is not possible without a display.

by morenito44

After reviewing all of the comments and suggestions, I decided to try to install XP via DOS (since my PS2 keyboard would not function in the XP install screen). This worked!! XP went and booted up. It's tru, the BIOS, OS and motherboard (for this Dell anyway)are all tied together. Thaks to all for all of the suggestions.

by samhobbs

You are probably correct. I think the Dell 4600 is too old to have support of a USB keyboard and that is why the keyboard does not work.

by morenito44

I did not intend to come across as criticizing. I thought you might be suggesting to reomove the AGP and use some other method to view what is happening. Please do not take what I said the wrong way.

by normshzu

My Dell 4600 Desktop Pentium 4 crashed routinely with Wireless USR card communicating with DSL WIRELESS Actiontec Router I switched to a wired NIC Internet Service and removed the wireless card and my system works flawless no blue screen of death issues. Try running and testing the system without wireless network card.

This discussion is closed to new replies.