Discussion Locked

DNS error 7062

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello. I have DNS running on a NT server with service pack 4.0. Operations with the server are fine, however, on a regular basis I receive an error in event viewer stating the following:
DNS Server encountered a packet addressed to itself - IP address x.x.x.x. The DNS server should never be sending a packet to itself. This situation usually indicates a configuration error.

I looked this error up on the MS web site and have followed all of the things that they say could be causing these errors. Nothing has helped.(EX: Forwarders, secondary zones, notify lists, delegations of sub zones).

Any ideas would be more helpful than you will know. Thank you in advance.

9 replies

by tracyg

Unfortunately this answer did not help my situation. As my question stated, I have already checked all of the areas that Microsoft says could generate this error and was unable to find a configuration error. I have done a lot of research on this error and I always come up with the same "Fixes" and the only problem is, as far as I can see, the areas they refer to that could have the self send capibility are all set up properly on my system. I do thank you for taking the time out to respond tomy question. If you think of anything else, please let me know.

by oskiller

Check the following areas for possible self-send configuration errors:

1) Forwarders list (DNS server should not forward to themselves).
2) Master lists of secondary zones.
3) Notify lists of primary zones.
4) Delegations of subzones.

Must not contain NS record for DNS server

Example: -> This DNS server dns1.foo.com is the primary for the zone foo.com. -> You have delegated the zone bar.foo.com to bardns.bar.foo.com and are NOT running the bar.foo.com zone on this DNS (dns1.foo.com). Note, you should make this check (with nslookup of DNS manager) both on this DNS server and on the server(s) you delegated the subzone to. It is possible that the delegation was done correctly, but that the primary DNS for the subzone, has any incorrect NS record pointing back at this server. If this incorrect NS record is cached at this server, then the self-send could result. If found, the subzone DNS server admin should remove the offending NS record.

by oskiller

(Since we are limited, I will continue the answer with comments)

To resolve this issue, check for the following conditions:

Forwarders:

DNS can be configured to forward off-site queries to designated servers. Be sure
that the DNS server is not configured to forward these off-site queries to
itself:

1. Select the server, click DNS, and then click Properties from the menu.

2. Click the Forwarders tab.

3. If the server's own IP address is listed, select it and click Remove.

Master List of Secondary Zones:

A secondary zone is configured with a list of the master or primary server(s). Be
sure that the server's own IP address is not listed as one of the IP master(s):

1. Select the secondary zone, click DNS, and then click Properties from the menu.

2. Click the General tab.

3. If the server's own IP address is listed in the IP Master(s) section, select it and click Remove.

Notify Lists:

Microsoft Windows NT DNS Server allows the Administrator to specify (on the primary DNS server) any secondary DNS servers that should be notified immediately of changes to the Zone file. Be sure that the DNS server is not configured to notify itself:

1. Select the primary zone, click DNS, and thenclick Properties from the menu.

2. Click the Notify tab.

3. If the server's own IP address is listed, select it and click Remove.

by oskiller

Lame Delegation:

Lame delegation is defined as having a domain or subdomain delegated to a server
that is not authoritative for the domain (in other words, a zone file does not
exist for the domain on the server). There are two possible scenarios that can
cause lame delegation:

- Delegating a Child Domain to Itself

If a child domain is created on a server and an NS record is added to that domain that resolves to its own IP address, an Event 7062 is generated. The followingis an example:

- DNS server ns1.domain.com is the primary DNS server for the domain.com zone. A child domain is created named child.domain.com and an NS record is added to child.domain.com for ns1.domain.com. This results in a child domain being delegated to itself. To resolve this issue, remove the NS
record from child.domain.com. Only add NS records to child domains if you wish to delegate it to another server (that is, to delegate it to ns2.domain.com).

- Domain Delegated to Server with No Zone File

by oskiller

If another DNS server has delegated a domain (either a forward lookup or reverse lookup domain) to a server and there is no zone file on the server for that domain, an Event 7062 is generated. The following are examples:

- Your Internet Service Provider (ISP) has assigned you the Class C network of 192.168.1.0 and has delegated the 1.168.192.in-addr.arpa domain for reverse lookups to your DNS server. If there is no zone configured on your DNS server for that domain, event 7062 will be generated every time a query is made for that domain from the server. The DNS server will step through the DNS hierarchy starting at the root servers and eventually receive a response from the ISP's DNS server indicating that the server itself is authoritative for the domain and attempt to query itself. To resolve this issue, either create a primary or secondary zone for that domain, or have the ISP change the delegation.

- Your ISP has delegated a domain to your caching-only DNS server. Because there are no zone files on a caching-only server, any queries that it makes for hosts that reside in domains for which it has been delegated authority will result in an event 7062 error. To resolve this issue, either create a primary or secondary zone file for that domain, or have the ISP change the delegation.

by tracyg

Unfortunately this answer did not help my situation. As my question stated, I have already checked all of the areas that Microsoft says could generate this error and was unable to find a configuration error. I have done a lot of research on this error and I always come up with the same "Fixes" and the only problem is, as far as I can see, the areas they refer to that could have the self send capibility are all set up properly on my system. I do thank you for taking the time out to respond tomy question. If you think of anything else, please let me know.

This discussion is closed to new replies.