Discussion Locked

Dual install WIN95/98

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have installed Win95 on a pc. No problems. I am trying to install WIN98 on the same machine (dual boot), but when I run the Win98 setup program. I get a message telling me that it has detected a installed operating system and I have to buy the upgrade version of Win98. Is there a way to get around it?

15 replies

by volovoy

You have to install software System Commander or something like this to make dual boot possible.

by m_fo

System comander is useful when you have both sysems setup. Not when seting them up.

by cdobbin

Try partition magic, I know it has a utility for creating a dual boot manager on you hard drive. Not sure if you can do this and maintain your original OS. I was messing around with and old pc and used P-Magic to create the partition and thats when I seen it, I installed it but never actually tried it, I ended up removing it and installing Red Hat on the box. I'd check it out and give it a try.

by pschuvie

By design Win9x versions do not include a boot manager, unlike say Windows NT. They never were intended to co-exist on the same machine or harddrive.

However, several companies see this weakness and have made a boot manager that supplements doing what you want to do.

I am unsure as to why you repond negative to System Commander as it is well rated and very successful in this area.

However, there are some other resources, like

Partion Magic includes Boot Magic
Partion Commander
BootIT

You should take a couple minutes and read through these helpful articles for insight

http://www.winmag.com/windows/guides/winme/27.htm

http://www.winmag.com/windows/guides/dualboot/

And I did run across on very unusual approach to this idea. I don't recommend it for the faint of heart but the program logic seems sound and it is a free way to get around the problem. User caution is advised.

http://www.webdev.net/orca/Dualboot.htm

HTH and good luck on your project.

by madcateast

Your rejection to the first answer is incorrect. System Commander needs win 9X installed first so that it can be loaded. It states this in the manual. It is helpful to already have your other partitions in place before you do this, if not SC has a partition utility with it. After all of this is done you use the SC utilities to hide the other OS?s on the system to install the next one. This is necessary with Win 9X or it won?t load as you have seen. With this set-up I have a quad boot system with Win 98, Win NT, Dos 6.22, and Linux. I could have used the boot loader in NT or Linux but just continued using SC. You also need to remember to put the boot information within the first 2 GB of the hard drive. In my set-up I have 2 HD?s with the boot portion of 2 OS?s on each and the other partitions for data and what not further in to the disk. It sounds harder than it really is, Plan out your partitions first and don?t forget about the 2 GB limitation. And remember to RTFM!

by alomer53

By design two systems cannot exist on the same PC. Yet , you could get around this by
doing the following:
1. Format your hard drive using an EZ software, then partion as required.
2. Install your operating systemin the appropriate drives(eg.Drive C: DOS6.22, Drive E:DOS8.xx, Drive F:UNIX and whatever...).
3. Install Win95 on Drive C:\ and Win98 on Drive F:\ and so on....
4. Instal any booting sequence software to
your liking or create one by using a batch
file in Dos's Q-Basic.

by bertievn

Another Tip, you can rename win.com file that windows will install
Visit zdnet.community/stories/main/0,9057,2662085,00.html
Good luck i gave up useing Bootit but were impatient
Regards
Bertie

This discussion is closed to new replies.