Discussion Locked

E2K can receive, not send to internet

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I ahve set up E2K with SMTP and a connector. My users can receive mail from the internet, but cannot send messages out to it.

The messages get stuck in the SMTP Queues. The Queue proerties report:

"The remote server did not respond to a connection attempt."

And this is for ALL messages.

I have configured my system like some others I know, and theirs works!

Help!

Jed

13 replies

by lordinfidel

Several questions..

Is the IMS service started?/You did us the Internet Mail Service Connector?

Have you checked DNS? (can exh resolve names)
What are your retry times set at/time-out period?

by jedavidow

There is no internet Mail Service Connector, this is Exchange 2000.
I have SMTP and a connector attatched to it.

I have tried several retry/timeout periods, from a couple minutes to hours.
Neither work.

The DNS seems to be fine. I just keep getting messages that the remote server is refusing connections to its SMTP.

by khenkell

Need more info:

1) Is the send failing for all email address ranges (like messages for someone@yahoo.com and anyone@redcross.org are all failing)? or is it just a specific domain (ie just messages to @yahoo.com, but messages to joe@aol.com work)

2) did you try to log into the remote smtp server manually? (via telnet to port 25?) This will oftern return a clearer error message and / or id whether or not the problem lies with DNS.

If you aren't sure how to do this, please let me know and I will post directions.

3)Did you create any address space masks (or is SMTP using the * address space?)

If this doeesn't work, let me know, there are plenty of more things to try, but I am limited in space.

I check here 2 or 3 times daily.

Hope this helps,
Keith Henkell
khenkell@chipscc.com

by jedavidow

1)All address ranges are failing.
2)I did not try manually. How do I do that?
3)I am using the "*" mask.

by khenkell

To check to see if you can send manually:

First go to http://www.demon.net/external/index.shtml
and select: Examine the DNS Data on a Particular Domain.

In the output you will see a line like:
hp.com mail is handled (pri=30) by smtpx.hp.com
Then open a trusty CMD or Command prompt and open a telnet session to the machine listed in the line above plus a colon and 25 (in this example you would type: telnet smtpx.hp.com:25)

This should open a session to the SMTP server where it will tell you what versio it is. You can now type in the following commands to send a test message (remember, you are bypassing your server to see if the fault lies within or outside of Exchange!)

by jedavidow

Yoiur answer was cut off, but that doesn't matter. All my telnet to port 25 connections (yahoo, hotmail, etc) get the following message:

"Could not open a connection to host: Connect Failed"

by khenkell

In the session type:

EHLO mail.yourdomain.com
mail from: youremail@yourdomain.com
rcpt to: thepersonyouaresendingto@theirdomain.com
subject: The subject line you want.
Type your message here....

Include a line with just a period and a return / enter key to send the message
.

----
Your message should now be sent. Check with the user to see if it was received. Note that this will only work when you change the above commands to match you the person you are trying to send to.

Try two or three associates that you can call to verify. Please remember to replace the yourdomain.com to your server's DNS domain and the theirdomain.com must be the one you looked up in the previous steps.

If it works, the problem is in Exchange. If it doesn't, it is probably a DNS or other similar issue.

Good luck and let me know how it goes. There are more things to try either way.

Keith Henkell

by khenkell

Sorry, the first part got cut off:

The EHLO and following lines are commands to enter in at the prompt in the telnet session. They ID your session and tell the remote server all about the message you are asking it to deliver for you. This is the language the servers themselves use.

by khenkell

Did you try the telnet sessions from the exchange server? If so, and it didn't work, you have now pipointed the problem:

SMTP is being blocked from your server>

There are two possible things that I can think of that are doing this:

1) You are using a proxy, a firewall, or NAT between your server and the Internet.

Check with your ISP to make sure that the exchange server has a public IP address (you probably do or inbound would not work) and that they are not doing the above anywhere between you and the Internet. Many ISP's block SMTP outbound.

2) you were blacklisted for sending spam or being used as a remailer for spam. This is less likely unless you somehow had a functional mail server before your exchange 2000 serverthat may have been compromised.

Your ISP should be able to help you with this.

Keith Henkell.

by jedavidow

Thank you! My ISP blocks all port 25 connections to prevent spamming. I now use their SMTP server as a smart host for my Exchange server and all is well.

This discussion is closed to new replies.