Discussion Locked

FDISK w/ FAT32X

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
How can I repartition a hard drive that has FAT32X on it?

19 replies

by billc124

You can as long as you have a version of FDISK that comes with Windows 95 OSR2 or Windows 98. The version of FDISK that comes with the original release of 95 does not support FAT32, nor does the DOS version. Bear in mind that this will not allow youto keep any data, if you FDISK, all data will be deleted. Hope this helps you.

by mchen

create a boot disk with a Win 95 OSR 2 or Win 98. you can than use fdisk to repartition the drive.

by chris hirst

As long as you have any version of FDISK from DOS5 onwards you can do anything you want with it. If you start fdisk and it does not ask if you want to use Large Disk Support it will be a FAT16 version, If you get the message enter "N" then when you select the delete partition option there will be a "Delete Non-DOS Partition" entry, select this, Follow the prompts and "Hey Presto" no partition. Obviously this will destroy any data you have but, you will have a valid backup of course.

Happy DOSsing

by neos_101

The Best way is to run Debug....
Even if you have repartitioned the hard drive, FDISK does not update the entire partition sector after the first time. The following DEBUG script will clear the partition sector (cyl 0, head 0, sector 1) of the first hard drive, which will force FDISK to completely start over. This is sometimes useful for removing Disk Manager or EZ Drive and should also remove any boot sector viruses, providing that the virus is not active in memory, which should be the case if you have booted clean from a non-infected diskette. Although this script clears only the first physical drive, we recommend unplugging other drives to prevent accidental data loss. Letters in script are not case-sensitive.

A:\>DEBUG - f 200 L200 0
- a 100
xxxx:0100 mov ax,301 (ignore segment:offset values at left)
xxxx:0103 mov bx,200
xxxx:0106 mov cx,1
xxxx:0109 mov dx,0080
xxxx:010C int 13
xxxx:010E int3
xxxx:010F (Press ENTER an extra time here)
- d 100 LF
xxxx:0100 B8 01 03 BB 00 02 B9 01-00 BA 80 00 CD 13 CC
(make sure that hex values match above line before proceeding)
(if values do not match, type Q and start over)
- g=100
(ignore register display)
- q (quits back to DOS)

FDISK should now show "No partitions defined".

by neos_101

The Best way is to run Debug....
Even if you have repartitioned the hard drive, FDISK does not update the entire partition sector after the first time. The following DEBUG script will clear the partition sector (cyl 0, head 0, sector 1) of the first hard drive, which will force FDISK to completely start over. This is sometimes useful for removing Disk Manager or EZ Drive and should also remove any boot sector viruses, providing that the virus is not active in memory, which should be the case if you have booted clean from a non-infected diskette. Although this script clears only the first physical drive, I recommend unplugging other drives to prevent accidental data loss. Letters in script are not case-sensitive.

A:\>DEBUG- f 200 L200 0
- a 100
xxxx:0100 mov ax,301 (ignore segment:offset values at left)
xxxx:0103 mov bx,200
xxxx:0106 mov cx,1
xxxx:0109 mov dx,0080
xxxx:010C int 13
xxxx:010E int 3
xxxx:010F (Press ENTER an extra time here)
- d 100 LF
xxxx:0100 B8 01 03 BB 00 02 B9 01-00 BA 80 00 CD 13 CC
(make sure that hex values match above line before proceeding)
(if values do not match, type Q and start over)
- g=100
(ignore register display)
- q (quits back to DOS)

FDISK should now show "No partitions defined".

by wlbowers

Buy a copy of partition magic. It works in windows. You can resize the current partition then add what you want.
Debug, Yea right.

Good Luck Lee

by billc124

I was just wondering why you rejected everybodys answer to this question. Almost everyone that posted an answer that was vaild and alot of people posted the same answer that I gave you first. Are you one of those people who gets the answer they wantand then don't give up the points? Whats up with that.

This discussion is closed to new replies.