9 replies
by sitchy Accepted solution
by hal 9000 Accepted solution
If the board is faulty that will cure your problem. However if the Motor in the HDD is faulty it needs to be placed in a Class 1 Clean Room and dismantled as the motor is enclosed inside the HDD.
If you have one of the highly filtered Lama Flow Cabinets you can get away with dismantling a HDD in that but if you have a power failure you can kiss the internals of the drive good by.
Col
by michael jay Accepted solution
by sitchy Accepted solution
by hal 9000 Accepted solution
The biggest problem is to find the right screw Driver Bit to undo the screws. Snap On has these or maybe one of the bigger Hardware Stores in your area.
As for the actual Circuit Board once you have the screws holding it in place undone you should lift it straight up there should be several Pins sticking out of the bottom of the case for the motor and a Ribbon Cable for the Read Write Heads which will either lock in place or just be a push in connection.
Most of the 2.5 inch drives are the push in connector but if you see what looks like a separate piece of plastic at the front of the Connector for the Ribbon Cable try easing it away from the Circuit Board. If it moves it will unlock the ribbon Cable and make replacement easier but you have to remember to lock it back in place.
Because 2.5 inch drives are small many don't have the locking connector for the Ribbon Cable and it's just a push in connection. When you have the replacement board connected to the Ribbon Cable drop it onto the HDD Chassis remembering to replace any insulation material that may have been in between the Circuit Board and the HDD.
I always use a Magnifying Light to do this type of thing as they are small and easy to make a mistake with. Once you have the circuit board in place screw a couple of the screws in to hold it in place and then mount it in the USB caddy and take your data off it.
You may need to take ownership of the files by following the direction's here
Also if you have encrypted the files you'll need to save the encryption keys by following the directions here
As for your data if the drive was working properly prior to the incident you should be able to recover everything but if it's been damaged along the line it may be necessary to send it away for a Data Recovery Service to diagnose the problem with the drive and recover your data if it's worth the price involved. A working drive costs about 1K to recover the data from and a lot more if they have to pull it apart and reconstruct the data that way. But if it's really important it's possible to recover the data though at a cost.
Col
If you are using a USB Caddy most 2.5 inch drives don't need a jumper fitted so if you have one fitted remove it and place it somewhere safe till you need it again. But I wouldn't recommend attempting to use that HDD again for anything important.
by michael jay Accepted solution
by sitchy Accepted solution
I want to say thanks so much for the info from both you guys. It helps my confidence. I have optical screw drivers that have fine phillips heads. Also Sears has them. I just noticed the HD I was thinking of buying on Ebay was sold. Its a Fujitsu MHT2030AT 2003-12 like mine. Others on there are different build dates. I heard somewhere that date could be significant.
I'm hoping to pull the data then put the board back in the new HD and installing it into my laptop. You said assy #'s are on those on the PCBs, Michael? Maybe I should buy a lot of 10 dead drives and check every board. My luck the one that fits is dead also. Col,I know the laptops have those flat ribbons that who knows what holds them in. My data(pictures of my airplane crash in AK) is worth alot to me but not 1K. Couldnt a person take a sand blasting box and put an air filtration(ionic breeze) with HD in there and after several hours of filtering take screws out on the label side? Im sooo hoping I dont need to go to that. Keep writing your knowledge is refreshing.
by michael jay Accepted solution
Do not remove the screws on the label side, there is nothing there but danger. If you have removed the bottom, the side with holes as I described you can now see the circuit board if you have a scanner copy it and send to me the picture, I am about to decommission 6 laptops and I may have a card with your numbers on it. Let me know.
By the way, when this is over you can go ahead and remove the screws from the label side note that one screw is under the label, then you will get 2 really shiny disks and a magnet of amazing power for its small size.
by atul_484 Accepted solution
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending