Question Locked

Hard drive not detected by BIOS

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I was trying to change power supplies from an old computer to my new one because my computer kept turning off in the middle of a game whenever i tried to play.

The old power supply didnt have enough components to plug everything into my newer computer so I just decided to put it back in the old computer and use it.

The old computer's hard drive was broken so I took the newest HDD and put it in.

Now when I try to turn the computer on it says:

"Diskette drive 0 seek failure
Primary drive 0 not found
Strike the F1 key to continue, F2 to run setup utility"

When I press F1 nothing happens, just a line that says something like "Press F1 to retry". F2 takes me to the setup and under hard drive it says "Hard Drive (not installed)".

Any idea why it isn't working? It was working before i took it out of my new computer so I don't think it's a problem with the hard drive. It's a different kind of hard drive than the old one too, the SATA cable is a thick pink cable, the old one was a flat cable.

7 replies

by salim

Your old system has a WIDE CABLE drive called IDE.
Your new drive is off SATA
THAT IS WHY IT does not detect new hard drive.
In order to detect this drive, you have to have IDE TO SATA Connector in the middle of old motherboard and new hard drive.

by oh smeg

Which are not interchangeable. The Drive Type that uses the Wide Flat Cable with a 40 Pin Connector is called IDE or Parallel ATA where as the one using the Thick Pink Cable is a Serial ATA or SATA drive type with a 5 Pin Connector.

You can not plug a SATA Drive into a PATA lead and even with a converter they are generally speaking not recognizable because PATA or IDE Drives have a Upper Limit in BIOS that [b]Can Not[/b] be exceeded.

If a PATA or IDE Drive has failed in a system it need to be replaced with a PATA or IDE Drive of a size compatible with the BIOS or you need to fit a PCI SATA Controller Card and reinstall the OS to the System and in the event of some kind of Windows OS you need to press the [b]F6 Key[/b] when the first blue screen appears and wait till you are prompted to insert the PCI Controller Drivers copied tot he Root of a Floppy into the A Drive and then press Enter.

You [b]Can Not[/b] move a HDD with a Windows OS Loaded between different computers and have it work. Windows builds a HAL or Hardware Abstraction Layer File which is basically a list of all the Hardware int he computer that it was installed on and if this Hardware is different the required Drivers are not present so the system fails to work.

So here I think you have 2 distinct problems the first is that the BIOS can not correctly identify this HDD because it is the wrong type for the M'Board and the Second is that the Installed OS [b]Will Not[/b] run even if the M'Board correctly identifies the HDD because it is now attempting to work with different hardware and doesn't have the necessary drivers available to it to do this.

Col

by dls318

The motherboard in the old computer has IDE and SATA drives.. it just isn't detecting the hard drive for some reason.

by dls318

I tried to reformat the hard drive with a boot cd, the reformat program didn't detect a hdd to overwrite stuff on though. I was using the CD & DVD that came with my Alienware (the newest computer).

by thumbsup2

... if the BIOS can't see the drive, the boot CD can't see it either.

by oh smeg

You need to press the [b]F6 Key[/b] when the first blue screen appears and wait till you are prompted to Insert a SCSI/RAID Driver in the A Drive and press Enter. Here you need to have the SATA Driver copied to the root of a Floppy available and then when prompted insert it into the Floppy Drive and press Enter.

That will install the SATA Driver and make the drive visible to the OS and the OS Installer.

If you don't have a SATA Driver and the System Makers or the M'Board Makers Web Sites do not have this you then need to enter the BIOS and set the SATA Controller to Native and save the changes when you exit the BIOS.

Col

This discussion is closed to new replies.