Discussion Locked

HardWare Raid

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have 3 NT servers..
Compaq Proliant ML370 and 2 Proliant 5500's
Each on has a hardware RAID with 3 9.2 GIG hard drives. Because we need to upgrade to larger drives with more space, we have purchased several 36 gig drives.

My question, How isit possible to install the larger hard drives to....
1. not lose any data
2. once the new larger drives are in place, the system will recognize the additional space.
3. Down time will be none or minimal.

I would appreciate any help. Thanks in advance

12 replies

by bobby gillette

Hey Michael...this is how I would go about it.

1) Do a full system backup of your servers, system/boot partition as well as your logical disk. (I assume you have the RAID partitioned).
2)install and configure your new 36Gb drives and configure your RAID accordingly
3)install WinNT and/or restore from backup.

**This is going on taking a couple of things for granted... a couple questions though. How do you have your RAID configured? RAID 3 at the hardware level and an install of NT from there or a system disk with two drives RAID 1?

-B-

by rabbit_runner

My drives (3) are all seen by the system, as a single drive. They are then partitioned into...
1. Boot/System partition (4 Gig)
2. Data partition of all remaining space.

Problem: I definitely do NOT want to re-install.
I know that what you have mentioned will work, but it does mean re-installing, even with the backup

by megtek

Hello...

I have used Server Magic by Power Quest. They also make Server Image. I use it at work on Novell and NT boxes. Just create an image of the data on the server, install the new drives, and restore the image. You can also use Server Magic to extend partition or volume sizes without losing any data.

Symantec also has image software - Norton Ghost. These imaging products should take you no more than 1 hour to get the new drives going.

by bobby gillette

Ah...what kind of backup software are you using? ArcServe and BackupExec both have options to restore from backup via a floppy. Your downtime would only be dependent on the speed of your tape drive...

As Megtek posted, an image would work, I recommend either Ghost or PowerQuest's Drive Image...

either way would provide the same result, but depending on the amount of data is on your array, as well as your connection to the network share you save the image to, I doubt you could finish the entire process in less than an hour...

-B-

by vagab0nd

Hi, Michael,

If you really do not want to reinstall, then Answers 2 and 3 will work and you should not have problems with system, but you may have some problems with Compaq Agents, so be ready.

by rabbit_runner

Would it be possible to do the following?
1. Since this is a 'hardware Raid', to remove one existing drive and insert the larger one. (they are hot-swappable)
2. Let it replicate the data
3. Replace a second drive and let it replicate the date
4. Then replace the third drive and let it replicate the data.

At this point, the data should be on the new drives, but the size of the drive will be equal to the original drives.

5. Now, use some utility, such as 'Server Magic' to expand the drives.

Does this option work?

by mservino

Here's a thought, since your updating your hard drives you may want to consider updating your raid controller as well to take full advantage of the speed of the new drives (I expect SCSI3-10K now vs 7200rpm for the old).

If you do this you can install the new controller, attach the new drives to it, then use one a utilites to mirror the image of your existing system to the new then just pull the old and reset the new as your primary boot.

btw- No you can't yank out a 9.2G drive and stick in a 36G drive.

you could ghost it, swap em, restore from the ghost image then use server magic to expand the drives, Ghost will recreate your existing partition sizes.

-Mike

This discussion is closed to new replies.