Discussion Locked

HELP! My Computer Turns On For 3 Seconds, Then Shuts Off 2.0

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

my system

INTEL CORE 2 QUAD Q6600 QUAD CORE 1066MHZ FSB
SPIRE HIGH PERFOMANCE CPU COOLER
ASUS P5B MAINBOARD 1066MHz FSB SUPPORT
4GB DDR-2 667FSB (PC5400) Memory
4X MEMORY HEAT SPREADORS
768MB nVIDIA Ge-Force 8800GTX DVI/TV-OUT HDTV PCI EXPRESS VIDEO CARD
400GB 7200RPM UDMA-300 SATA II Hard Drive 16MB BUFFER
Western Digital WD10EACS 1TB SATA2 16MB Hard Drive
THERMALTAKE HARD DRIVE COOLER
20X LITE ON DUAL LAYER DVD-RW DRIVE W/ LIGHTSCRIBE
LITE ON DVD-ROM DRIVE
10/100/1000 GIGABIT Fast Ethernet Network Controller
WIRELESS G CARD
CREATIVE LABS SOUND BLASTER XTREMEGAMER 7.1
BFG-PHYSX 128MB
X PLORER BLACK Case w/ 600 WATT Power Supply and Front USB Port
DELUXE COOLING PACKAGE (3 HIGH PERFORMANCE CASE COOLERS)
Keyboard / Mouse : LOGITECH
Speakers : LOGITECH X530 5.1 SPEAKERS
Monitor : ACER 19" LCD MONITOR
Operating System : WINDOWS Vista 32bit

I was playing a game when my system shut down. When I rebooted, a screen came up saying the system could not over clock and to press F1 to configure or F2 for default settings. My system was never over clocked so I pressed F2. It booted up normally. I got back into the game and the system shut down again. This time when I pressed the power button, the system would come on (LCD lights, fans and HD, but no bio beep) and shut down after 2 seconds.

I went to another board and found this thread.

http://www.tomshardware.com/forum/246825-28-computer-turns-seconds-shuts

I dont have the tools to disconnect and place the components on plastic or card board, so I started with the things I could try.

1. I tried the power button. when i pressed and held it in, the box would power up, fans would start, but still no system boot or bio beep. as soon as i unpressed it, it would power down. There is no physical switch that I see to test it without the power button, so I made sure the wires were connected to the MOBO.

2. checked the heat sync and CPU. i unscrewed the heat sync and checked for heat on the chip. no signs of over heating or bad connection with either.

3. i cleared the CMOS memory and reset the battery. when I did this and rebooted, the system will now stay on (just like if i kept the power button pressed in) but never boots up at all.

This is where I am... can anyone help? I have a Flip cam and will be happy to shoot video or take pics if needed.

Thank you!

10 replies

by mjd420nova

This certainly sounds like the power supply has died. It may have worked okay for a while but the specs on the rest of the system tells me that you didn't have a big enough power supply to start with. Try replacing the power supply with one that has at least 750 watts and see how it works out.

by nicknielsen

your CPU is not completing POST, the power-on self-test. The over-clocking error message is a clue to the failure: either your motherboard or your CPU has probably kicked it.

Check your mainboard for swollen capacitors (the tin-can looking things pictured here: http://www.badcaps.net/pages.php?vid=5). You can also try reseating your memory and processor, but I think you'll need to spend a dollar or two to get your system back up.

etu

by ecabell76969

thank you mjd420nova and 7NickNielsen. unfortunately i do not have another power supply to test, but I checked the capacitors. all the capacitors seem ok besides one. it is located by the video card. there is no electrolyte on the board, but it is slightly bulged.

I also reset the RAM chips (not the CPU). when i tested it, I get the same results... power to the PC (LCD and fans) but will not boot. the LCD lights keep blinking on and off in 1 sec intervels.

by nicknielsen

One way to see if the power supply is overloaded is to disconnect all devices that are not necessary for the system to boot: DVD burners/players, secondary hard drives, etc. If the system now boots, you need a larger power supply. If the system still doesn't boot, check the power supply.

This article provides some excellent tips and procedures, as well as the pinout for the mainboard P1 connection: http://articles.techrepublic.com.com/5100-10878_11-1056686.html. You will definitely need a multimeter. If you don't want to test the power supply in the PC, you will also need a power supply tester, available on-line from Newegg.com or at your local electronics store.

If the power supply tests good, you will need to find a way to test the mainboard and processor and see if they boot in another box.

edit: missed a step

by ecabell76969

thank you nick. that is a great link. I disconnected my 2nd HD, all CD ROMS. I only had my main HD, video card and 2 sticks of ram connected. still the same result.

My board is ATX, but I do not have another PC i can try and swap ut the PSU to se if that is the issue.

by nicknielsen

as outlined in the link on the installed board and they're all good, you may just want to go ahead and buy a new mobo/processor combo.

I know, of course, that such a trivial expense will be no problem for you! ;)

by ecabell76969

i dont have a way to check the voltage at all and I dont have the $$ right now to buy new stuff. I was hoping there maybe somthing i can try to jury rig. i am just sol at the moment... lol.

ty so much for the help.

by nicknielsen

Although I'm pretty certain they will check good. Perhaps one of your friends has a multimeter you can borrow, or you can pick up a digital multimeter at Sears for around $20-$25.

Wish there was a better way, but I don't know of one.

by amrrafie

Could be a CPU fan issue.. system would shutdown if the CPU ran too hot, and i doubt you would see any sign that its over heating.

You could try running the CPU at a lower speed.

This discussion is closed to new replies.