Discussion Locked

Help with setting up print server

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi everyone. I have dont know how to setup a print server. I am using NT 4.0 server and 4 printers with ip addresses on the network. I have an existing print server but it needs to be replaced asap. What are the steps to setup a print server?
Some of the questions I have been asking myself:
1.) will changing servers create problems for users? If so, what should I do?
2.) Is there any way to minimize the impact on users? If i change servers, will the users who have existing printerssetup have problems printing?

Thnaks for your help!

18 replies

by ippacket

If you are replacing an exiting server, you can install the NT on the new machine as a member server of a domain using any name you choose. To ease the migration of users, install the printers on the print server using the same share name that they are currently using. After everyone has gone home for the day take the original server offline. Remove any WINS and DNS entries for the original print server. When that is complete, rename the new server with the name of the old server. If you wouldlike use the same IP address (optional). When your users come in the next morning, they will not know the difference.

After the server is built and the printers installed on the new machine, it only takes about 30 to 45 min to do the name changeportion. Therefore, if you can get that much time for a loss of service, do it during the day.

by tejota

It's all a matter of how much flexibility you have with your network and servers. Probably the easiest way I can think of is to rename the servers. Name your new server the name of your original print server, don't forget to rename the original first. Install your printers with the same share names they had originally and whalla. Users who go to print to \\serverA\printerB will be able to print because they're printing by computer name and share name, not IP address. There is also a tool in the Resource kit called printmig.exe that will backup your existing print configuration from the registry into a file. Then you just run that file on the new server and it installs all printers and shares on the new server. You might have to re-install the drivers though if they're not your everyday run of the mill drivers that NT has. Hope this gives you some ideas.

Later,

TJ

by tejota

By the way, if you do change the servers where the printers are it will impact the users and they will no longer be able to print. They're printers point to a particular servername and share.

by estebandelatorre

You should preserve the shared printer name in order to make it available to every user without any problem.
Select a windows NT server and install the printer locally with admin rights, share the printer and that's all!!!
From Wks, select installa network printer and browse to the \\server\printername, selectit and you're done.
everyone can print to the share name or the pc's ip address.

If the printers have a nic card, thing are different. From the printer, create a port for that printer (lpr or the one provided by your printer manufacter) Install the port first, then install the printer as usual. and share it to the network
From wks, select install a network printer, browse to the \\server\sharename\ and that's all.

Also if you want only to print using IP only, when selecting a port choose lpr, insert the ip twice like: 129.11.11.52:129.11.11.52, set up the drivers and you are ready. Disadvantage: Need to setup drivers for every wks.

Good luck

by rondickersonjr

Thanks for the advice. Although this didnt help my situation, i really appreciate you taking time to answer! Thanks again!

by soekratis

Having more than 1 print-server will not cause any problem to your network. It is a good idea to setup the new print-server before removing the existing one. On the new print-server, set up the necessary ports and drivers and shared printer names. Now, once this is done, you can advise the users to looks for these printers on the new server that you have setup. That way, the transition will not affect or cause any downtime.

regards
Soekratis

by brett

the best way is to install a new LPR port (if this option is not available under "New Local Port", make sure Microsoft TCP/IP Printing is installed). Sometimes using LPR is even better than using the print servers own printing software! (as is the case with some Accton print servers).

just beware that some print servers are a tad finicky as to what LPR port name they use... also, in some UNIX environments, it can also affect how text and graphics are printed out - for example, with HP's and Lexmark Print Servers, put in the IP address, but for the Port name, use "TEXT", as sometimes it can cause text carriage-return/linefeed problems... consult documentation that comes with the print server for more info...

by rondickersonjr

thanks for taking time to answer. i have added more info; please reply again if you have any advice. thanks!

by @lberto

Hello There,

Good question, remember that every single change you made on your network will affect users no matter how small it is, the important part of it is to have all the tools and the knowledge and be prepared for eventualities to happen.
If I were you, I will setup a new server, different name, different TCP/IP, use the same share name, define all the queues exactly the same way that the actual server has. Do you have any Netport or software to manage all the printers, well, if you have a Netport program installed, just install it on you new server, make sure it is configure the same way. If so, you can test your printers from this new server and they should work. Remember to make sure all the printer have the same share and permititions so don't disconnect any user by mistake.
When this is all done and double check then take your old server down, rename the new one and make it the same name as the old one, as well as the same TCP/IP address, it is very important, because some mappings (some of them) are based on TCP/IP Addresses and not on WINS names; after this give it a try, it should work !!!
The important thing is you know all the steps you've made and have the old Print Server available just in case you have togo back to your old situation, which I don't think you'll have to.
Good luck,
@lberto

by rondickersonjr

I have been following the advice of several of your answers, and so far here is what i have accomplished:
1. Existing print server setup with 4 printers using jetdirect ports.
2. I have created a new server, installed jetadmin, and successfully created printer ports as they were on existing print server.
3. new print server name and ip address different. So is gateway(different building).
4. I now have both print servers up and running. Both print servers show printers in 'add printer' field. I can select from both print servers on all machines(I am assuming this because I checked a couple other PCs).

Now for the problems:
When I bring down the old print server, rename the new print server to the old print server, I get RPC error message: 'No RPC Server available'.

I then have to bring up the old server and power down new server.

Anyone suggest what I have done wrong, based on info given? If you need minute details, I can give them. Thanks again.

by estebandelatorre

Another try:
If your ip network, is different, the best solution will be: Show your users how to print on the new one, let both running for a month, and then bring down the old one.
But if the IP address is different but in the same network, consider first change the ip address to the old one.

by rondickersonjr

All of you - thanks for taking the time to answer my question. Unfortunately, I found none that helped. What I was looking for was a step-by-step process to setup a print server. What I got from most was general info.

'What are the steps to setup a print server? '

That was my first question. Everyone forgot to answer the most important one - setting up a print server! Basically I had to learn it myself, and thats why I awarded no points.

Thanks again.

Ron

This discussion is closed to new replies.