11 replies
by dmiles
You cannot install,windows 98 after XP because to the file structure and startup files.
If you are trying to dual boot XP,then install W98 first,then install XP.
The crude method of install OS on different hard drives,would be to disconnect XP drive,then setup the W98 drive as the lone drive and install OS,then set the jumper configuration as master/slave when you install the other drive
by otl
by cprada81
by yornthadude
I suggest partitioning your harddrive with for example partition magic (PM)6 or higher. Then take about 10 gigs from your existing partition which should be fat32 or ntfs. When u created free space create a new fat32 partition. which will be c: or e:. Now u can switch the primary partition with the build in PM bootloader. and start installing after next reboot.
p.s. make sure u have PM on cd cause u can't switch back from win98 to xp if u dont have the bootloader installed. Its also possible to create a little bootpartition from about 5 megs and install a third party bootloader from the internet in there.
Good luck !!
by bbbucko
What about the data?
You could always ghost your XP install but I'd just back up your data to CD or a removable drive
Then you really do need to scrub it and install the 98 1st - you thank us down the track :)
- 2 Partitions: Primary must be at the start of drive, FAT32, and recmnd 2GB-10GB
- Install W98 to Primary Partition
- Install XP from within 98 (boot to 98 first) to 2nd partition. If you want to access your XP drive from within 98 then make sure the XP partition is FAT32 also
Enjoy
by georgian3000
yes the answer is ,"You cannot install", windows 98 after XP because to the file structure and startup files. if you want ot have win98 as well as winXP that is dualbooting system, you should i meen not only you but it is a rule implied to everone that you should first install win98 and then XP,
see the funda is some what like this,95,98,nt,me,2000,xp, follow this procedure you cannot install 2000 after installing winXP, or winNT after 2000,i hope i have explaned to you very cleary.
its all inthe file structure.
The crude method of install OS on different hard drives,would be to disconnect XP drive,then setup the W98 drive as the lone drive and install OS,then set the jumper configuration as master/slave when you install the other drive
Tharun
According to procedure,the older OS must be installed first follow by new OS..
But,you may actually install win 98 after having installing win xp.All the windows boot file will be placed in c drive automatically.After installing win xp,do a backup for ALL the boot file on the c drive to another partition before installing win 98(is only about 120MB for win xp).After installing win 98,copy back the files the you have backup just now to c drive.....hope it helps...good luck!!
by fanku
If you want win98 to install...
then best and right way is...
format ur pc.
make 2 or 3 partition
and then 1st install windows 98 on Drive C:\
and then install windows XP on Drive D:\
as already you have winxp on drive D:\ but since system copy some file on dirve C:\
so u cannot install windows 98...
best follow the instruction what i hve give for best result.
by jct134
****PART 1****
How do I install Windows? 98/Me after I've installed XP? (without 3rd party software)
Here is one way to do it.
Necessary Criteria
This procedure assumes that Windows XP is installed on drive C: No support is offered for other drive letters.
Drive C: must be FAT16 or FAT32 to be able to install Windows 98/Me after XP is already installed. The 98/Me installation routine cannot write to an NTFS partition.
If your C: drive is not FAT or FAT32, you CANNOT complete this procedure. You will need a 3rd party boot manager. I recommend BootIt Next Generation, www.bootitng.com.
You must have a second hard disk or partition formatted for FAT16/32 in order to be able to install Windows 98/Me. Installing 98/Me to the same partition as Windows XP is NOT RECOMMENDED!
I recommend the use of a Windows 98/Me Startup disk for this procedure. If you don't have one, you can download the necessary files from http://www.bootdisk.com You should ensure that DEBUG.EXE is on your Startup disk. If it isn't, it can be copied from the Windows\Command folder. On a 98/Me Startup disk, created from Add/Remove Programs, its in the EBD.CAB file on the Startup disk. For a 98 Startup disk created from FAT32EBD.EXE its on the floppy
Installing Windows? 98
1) Use a Win98/Me Startup disk (with CD support) to boot your computer.
2) Insert your Win98/Me CD into the CD Rom drive.
3) At the A: prompt type X:\Win98\Setup.exe (for Win98) or X:\Win9x\Setup.exe (for Win Me) where X: is your CD-ROM drive.
4) Proceed with the install. When prompted for the install location, you'll see C:\Windows.000. Choose Other directory and change this to the drive you wish to install 98/Me to and name the folder Windows (or something else if you prefer).
5) Complete the Win98/Me install. Allow the computer to boot into Win98/Me.
by jct134
PART 2
Repairing the Windows? XP Boot Loader
1) Create a Win98 Startup Disk
2) Create a Notepad file with the following entries, exactly as shown:
L 100 2 0 1
N C:\BOOTSECT.DOS
R BX
0
R CX
200
W
Q
3) Save the file to the Win98/Me Startup Disk as READ.SCR
4) Boot with the Win98 Startup Disk and at the A: prompt type
DEBUG
by jct134
ANOTHER OPTION MIGHT BE THIS:
I also think that if you had 2 hard drives, you could remove the one with XP on it, set other as primary, boot to floppy and install 98 on that hard drive, then reattach the XP hard drive as master, and win98 as slave, then re-configure the boot.ini file on XP to Dual boot, but I am not sure as yet what all is needed for this method.
This discussion is closed to new replies.
Trending Windows Forum posts
Sort by Trending