Discussion Locked

I am having problems upgrading to XP from ME

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I currently own a Sony Vaio PCV RX-280DS which comes with ME factory-installed. I have been trying to upgrade to Xp, but to no avail. The problem I am having is this:
I started the setup program and it went through its routine of intalling setup files etc. Then it restarts, and the touble begins. The computer tried to load XP to finish setup, but it wouldn't; I got a stop error instead. I restarted the computer to try to find help with Sony. I restarted again and tried to continue setup, upon which I got a different error: "INF file txtsetup.sif is corrupt or missing, status 14. Setup cannot continue."
I have about run out of things to try.

13 replies

by thomastri

I have had a problem with XP Usually if you have trouble with an upgrade; try doing a clean install, if you only have an upgrade disk it is designed to detect any instance of windows on hard drive and install. The problem I had was the Bios wasn't compatable I had to replace my PC. This was overdue I was running a intel P3 667MHz processor. I heard a lot of issues with the ME version see if you can get a old win 98 disk and try once more. If you start getting lockups or file corruption errors you might consider a Bios upgrade.

by jdclyde

First step is make sure that your system devices will support XP and download all drivers and burn to CD.

Then get ME off the system.

Load Win98.

Look for the BIOS update.

Then do your XP update.

If it still doesn't work look at running a cd drive cleaner disk and make sure your XP disk is good.

[b]If that still doesn't work, post in the Tech Q&A section as this is a problem seeking an answer. The XP boys will come out to help you with this.[/b]

Good luck.

by Member 23058027

How old is this Vaio? As others have said wipe ME, upgrade the BIOS and do a clean install.

If you can't get a BIOS upgrade it could be time to get a new machine.

by powerman

I had the experience when switching to XP my PC used to have more and more system failures. I thought that reinstalling the operating system would fix this. But then I wasn?t able to install Win XP. It went neatly through the whole system of the installing process but then suddenly failed. Any new trial delivered a warning that file xy is missing or corrupt.

I?ve learned from the internet that sometimes this warning appears when system ram is damaged even if the bios test doesn?t reveal anything.

Since I had two banks of RAM installed, I took alternatively one of the banks out and tried to continue with the istallation of XP.

Luckily it worked with the first trial. When I inserted the damaged RAM the System stuck on the same error report as above.

Now I bought some new RAM and the system works smooth as before.

Before buying a new system just check this out.

Best wishes

PowerMan

by data ninja

Microsoft has stated that upgrading from ME to XP is not supported, period. But then there have been users that have figured ways around this, and there have been some mention of it in the MS Knowledge base.

Your best bet is to save/copy all of your data files, OE files, etc. to a temp directory and wipe out the ME OS and put Win98 on and install XP - OR - burn your data off to CD and do a full install of XP then copy your files back.

If it's an upgrade version there is a little trick that has been used. The short form is: put your hard drive on another system that has XP (after you backup your data files), delete the partition and re-create it as an NTFS partition, then put a "win98" directory on it with a copy of the win98 system files to "fool" the upgrade disk, but tell it to install to a different directory, ie, "windows"! There has been a mix of success/failures related to this method, so good luck...

by acecc

I choose to upgrade by booting from the CD. The installer with prompt you for the ME install CD.

BSOD is most likely a driver issue, ACPI. Are you upgrading from within Windows? or are you fresh booting from the CD to install?

Dump BIOS Extended Settings(CMOS)
The CMOS Clear method is differs depending on model and mfg. Look in the manual for the method to use.

Hardboot. RUN a disk partioning program and see what partions are on the HDD.

Either delete all Partions with FDISK, NTFS is seen as Non-DOS, I believe. OR RUN a Disk Prep Tool and wipe the drive.

Think about WDM and visit:
http://www.microsoft.com/resources/documentation/Windows/XP/all/reskit/en-us/Default.asp?url=/resources/documentation/Windows/XP/all/reskit/en-us/prkd_tro_vfxu.asp

by damian205

I have experienced this problem with upgrades to Win2K and XP. Both times the problem was the memory. It seems that because OS's loads so much into RAM if any of the memory is even a little bit dodgy then the installation will fail.

by ztdaniels

I suggest you visit the Sony web site. Your model came with several drivers specific to Sony and if you give them the model No. and that you want to up-grade to XP, they will give you the drivers, and programs compatible. They will even give step-by-step instructions for the conversion. good luck

by ocean1

But, you can also try to nook your machine. i work with financial data and whenever we need to change anything in the systems we dont upgrade we just save the files nook the machine and set it up with a clean version of the os. it has worked for me in all brands of machines including sony. go online and look for BOOT AND NOOK youll love it.

by aaron a baker

This one almost drove me crazy.
I went from an ABit KT 7A Raid Motherboard, 1.2 Gb CPU with 768 mgs of SD Ram running my Windows ME and everything was fine. Then I installed the XP over the WinME, Upgraded and everything was still fine. Then for some reason it crashed. By then I had changed Motherboards and gone from a 1.2 CPU to a 2.8 Gb and from 768 Mgs ram to 2Gb PC133 400Mgrz DDR Ram. All was working very well with the new stuff as well. I then tried to re-install my WinMe. All went well until the restart point and then it would go into the safe mode menu, you know pick a number as to how you want to start? It took me two weeks to figure out that the problem was I had "too much Ram". I yanked a stick, bringing me down to 1Gb and the thing went in smooth as butter and then re-added my XP.
What I had forgotten was that after a certain amount of ram, 968mgs "I think" 98 and/or WinME don't recognize it and goes into a redundancy loop. It keeps shutting down starting over and always ending up that the same place, the menu with the 1 to 4 choices. If I were you, I would remove some Ram, at least to a point around 700 mgs and then try installing your ME again. You might find this will solve your problem. I would further suggest that you consider just go ahead and install the XP Directly, then you shouldn't have any problems. Just out the CD in the Rom and have the system BIOS start from the CD Rom, follow the instructions and your in.
Good Luck
Regards
Aaron :)

by tomj001

I had a similar memory problem as Powerman. What I would do is try switching the memory sticks around, if you have multiple ram sticks
installed on your computer. A good stick can carry a slightly damaged ram module as long as the good one is in the first slot.
I say this because if your running with say; 128 mb which is low a amount of memory, your going to have a really slow installation. My setup was an XP Home Upgrade from Win98.

This discussion is closed to new replies.