25 replies
by cyberghost_1 Accepted solution
by santeewelding Accepted solution
by tobif Accepted solution
I quote:
My supported Memory types are DDR2-400 and DDR2-533 up to 2GB.
Since your memory modules are capable of responding even faster, the system uses it at the maximum speed the system can handle, namely 267 Mhz (corresponding to DDR2-533).
It's quite possible that the ratio between processor speed and memory speed would be different if you had a different type of processor, but I'm not sure. (It's simply not my area of expertise)
by who am i really Accepted solution
required for dual channel mode functionality,
one stick, can't, won't & doesn't do dual channel mode
if you're seeing single channel mode then you don't have the 2 sockets filled, or the modules are mismatched and can't operate in dual channel mode
by cyberghost_1 Accepted solution
by oh smeg Accepted solution
To the FSB of the CPU. What you need to understand is that the CPU works best in Dual Channel Mode and when set that way with 2 Identical RAM Modules each RAM Module runs at exactly Half of the Rated FSB Speed. So you have 2 Channels of RAM feeding a 533 MHZ which is what the CPU wants not what the RAM is capable of feeding it at.
There are other Limiting Factors involved here little things like the Chip Set of the M'Board are important but as the Atom CPU can only work at 533 it is being feed at 266 MHZ which is the fastest that 1 Module in Single Channel Mode can work at and still keep a stable CPU.
Doesn't matter what the RAM is capable of running at just what the CPU and Chip Set Supports. So if you where using 2 Identical RAM Modules in Dual Channel Mode it would show 533 MHZ but even still each RAM Module would be running at 266 MHZ which when doubled as there are two of them gives you 533 MHZ. ;)
Col
by cyberghost_1 Accepted solution
by oh smeg Accepted solution
To use Dual Channel Mode you need 2 RAM Modules.
If you can not install 2 RAM Modules the unit is restricted to Single Channel Mode unless the makers have done something very tricky with the M'Board Chip Set. While it's possible to use 1 RAM Module in Dual Channel Mode it involves using Double Sided RAM Modules and treating each side of the Module Separately. So if you have 1 Single Sided Module it acts like Single Channel RAM and if you have a Double Sided RAM Module it acts like Dual Channel RAM.
As this is a Expensive Trick for a NetBook it's very unlikely to be involved so the RAM will stay in Single Channel Mode and run at 50% of the FSB of the CPU.
Col
by oh smeg Accepted solution
If the M'Board requires SO DDR11 RAM you can not install SO DDR1 RAM. The layout of the RAM Module is different and DDR1 Modules will not fit into a DDR11 or DDR111 Socket. The same applies in reverse so the different RAM Modules are not interchangeable.
If it's designated to use DDR11 RAM that is what you need to buy.
You can also check out the Corsair Memory Locater here for your System
Col
by tobif Accepted solution
It was mentioned before in this thread, but just to make it more clear.
If a computer has a max speed for addressing the memory, then you'll get max performance if your memory meets the same speed. With faster memory, you won't get any further speed boast. The only thing that will happen is that the memory will have stabilized its output for some while when the computer gets around to reading it.
Reasons to buy quicker memory could be availability, price or plans to reuse same memory in future systems with higher speed.
(But always carefully check recommendations, some older systems and memory types could misbehave with too fast ram installed!)
by who am i really Accepted solution
HP/Compaq usually have one slot in the bottom, and the other is under the keyboard
if your system shows it has RAM but there's nothing in the slot in the back then you have one under the keyboard
by cyberghost_1 Accepted solution
by who am i really Accepted solution
skip looking under the keyboard:
your system:
Compaq Mini CQ10-120LA Netbook
according to Kingston's RAM search
the system has only one RAM slot
uses 800MHz RAM
a netbook isn't supposed to be a performance house
intended use of a Netbook, is web surfing, checking email, etc.
and maybe playing a bit of music
so it's no surprise that it's not configured as a dual channel system
by cyberghost_1 Accepted solution
by seanferd Accepted solution
by cyberghost_1 Accepted solution
by who am i really Accepted solution
only means that there are RAM chips on both sides of the module
it doesn't mean there is a separation,
however, if you bump your system from 1GB to 2GB you will get a performance increase regardless
for the record, I've never seen a single sided DIMM or SODIMM that's larger than 64MB
everything 128MB and up has chips on both sides
even the old 30 & 72 pin SIMMs had chips on both sides
only 1MB and smaller 30 Pin and 4MB & smaller 72Pin SIMMs had a single sided layout
I believe the reason they limit the Netbook systems to 2GB RAM in this fashion is because most ship with win7 Starter which has a programmed limitation of 2GB RAM anyway,
and dual channel mode wouldn't help with surfing, checking your email, using media player etc.
by oh smeg Accepted solution
I have just removed several 1 GIG Sodium Modules from a NB that where Single Sided and replaced them with 2 GIG Modules to max out the NB.
There are quite a few 1 GIG Modules out there that are Single Sided but that depends on the maker mostly. I have also several 1 GIG Corsair DDR2 Modules which are single sided so it depends on the capacity and maker as to which way that they come. ;)
Col
by who am i really Accepted solution
they're single sided because they're made of salt
did spell check get you?
SODIMM shows as a spelling error here but I don't let it "correct" the "correct" spelling I typed
by santeewelding Accepted solution
More better.
Besides, Emeritus Smeg gets to spell it any way he wants.
by seanferd Accepted solution
by santeewelding Accepted solution
I inherited a vial of sodium pellets, once, from a student of my class. They were submerged in kerosene. For years, I would pluck one or two out with tweezers and drop them into a quantity of water. The pellet would propel itself maddeningly all about, generating hydrogen gas as it went.
Finally, despite the kerosene, and after years, the pellets grew a fuzz about them.
Dumpster.
by ansugisalas Accepted solution
and not crucible? :D
You know you can electrolytically make sodium of salt too, right? But since it reacts with water it can't be solute... you have to melt it instead.
by oh smeg Accepted solution
Sodium Filled Valve for me. One of those old Aircraft type that had this soft metal inside them to aid cooling.
I would be very interested to see that thing welded. Provided of course I wasn't in range of it when it goes off. :D
Col
by ansugisalas Accepted solution
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending