Question Locked

Is my LAN card faulty??

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,
I work on windows XP (SP 2).
The LAN card i use is "Asound 10/100M Based Fast Ethernet Card".
Now i never really had used it as my Router had a Usb connection so never used the LAN card for an internet connection.
Recently purchased a Laptop and i wanted that it should also be able to access the internet, so there comes the need of the LAN card in the desktop.
Now the Router has DHCP enabled, connected a LAN cable to the Laptop and it works fine but when did the same with the Desktop, it nearly froze.
Went to the N/w connections to see whats going on and there it shows its busy getting an ip address.
Checked the LAN card's status in device manager and it says the device is working properly with the drivers being fine.
Sorry for the long explaining part :)
So the question, should i get it replaced or there's some tinkering to do??
Would appreciate all the help i can get
And am sure its a Router not a modem.

8 replies

by thumbsup2

Are you trying to connect the laptop via USB and the desktop via LAN cable? If so, it won't work. The USB/LAN connection is an either/or situation.

Does the router have more than one place to plug in a LAN cable? Or, is this really just a modem provided by the ISP and not really a router?

Does it have wireless capablility?

by asher2jk

Nopes, am trying to connect both the laptop and the desktop via LAN.

Yes it is a router as it has 4 LAN ports and one USB port. It has been manufactured by Huawei (MT841)

Well i guess it has wireless capability.. guess because.. it has 4 LEDs for LAN, 1 for USB and 2 for WLAN.. but i don't know why the Laptop isn't able to detect the SSID. I mean have logged into the Router settings and checked everything but still does not help.. don't worry this will be next question :)
But first i need to figure out what's wrong with the NIC card on the desktop!!

by ic-it

A lot of times the modem will lock onto the first device's MAC and will not allow the next device to receive a proper IP.
You need to do a hard reset of the modem (power down, wait 30 seconds, unplug the incoming connection, power up, plug in the incoming connection, and cycle the power one last time.

by asher2jk

Its not a modem.. its a router.. and since it has a ASIC chip i don't think it should face this problem.

by jiminpa

Do you get a link light when you plug the desktop into the router? Have you tried to ping the loopback address? 127.0.0.1 If you can't ping the loopback address then the game is over, bad NIC thanks for playing. If you can ping the loopback, and you are getting a link light, try assigning a static IP address with in the same subnet of your DHCP scope. If all seems well after doing that, try pinging your local IP address then try pinging the default router IP address, slowly make your way further away from the local PC with your pings.
If you do not get a link light, try a new patch cable, plug into a different, known working port. If all that fails... maybe the NIC is bad :)

by asher2jk

Well the link light does turn on.. but the loopback thing never came to my mind.. lemme check and will let you know..

by asher2jk

Well was able to ping the loopback address.. was also able to ping the static ip that i had given to it.. but strangely enough it was not able to ping the default router address.. this one took me off-guard. (one more thing that i wanted to add was the computer hanged for every now and then for about 2 seconds as if it was searching for something??) and kinda repeating myself the desktop was never able to receive an ip from the Router, had to assign a static always to make work.. it froze the computer otherwise..
The cables are good.. had checked them with the laptop.. so are the ports

This discussion is closed to new replies.