Question Locked

missing DVD-rom

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

hi to all experts here, desperately needed help here, pls shed some light...

my comp initially has
2 HD (C: & D:)
1 DVD burner (E:)
1 DVD-rom (F:)

everything was running fine for years. yesterday i tried to plug in an external DVD burner and all of a suddent this ballon pops up in the system tray. it disappeared real quick and if i remember correctly, it said sthg about "a device cannot be recognized by windows, to troubleshoot..." after seeing that i clicked to windows explorer and immediately noticed that my F: drive is not shown anymore. i clicked to device manager and i see no yellow question marks... i rebooted a few times and problem persists.... i tried going into BIOS at start up ... under IDE devices, i see:
Primary Master: DVD burner
3rd IDE Master: HD 1
4th IDE Master: HD 2

is there suppose to be a Secondary Master shown too!??! is this the problem?! my motherboard is an ASUS P5GD1 back from around 2.5 years ago...

what should i do to get my DVD-ROM (F:) drive back pls??? anybody pls help!!

7 replies

by milos.hyravy

Have you tried push the power supply plug further against the socket on drive?

I am running very old system as well and I have the same problem sometimes. But in my case the drives are disappearing mostly when I touch the cables inside the case etc.

My guess, as motherboards is little older. There might be a trouble as battery is running out of juice and/or power supply unit can not provide such a big amount of power to your components.

I would definitely try to go back into the previous working state with 2 drives and no external one. Just to make sure nothing is wrong with your DVD-ROM.

Give it a try! And always remember things are just getting worse ;)

by hal 9000

[i]Primary Master: DVD burner
3rd IDE Master: HD 1
4th IDE Master: HD 2[/i]

With IDE Drives you have a Master & Slave and you can only have a Primary Master Primary Slave then a Secondary Master & a Secondary Slave.

Sorry but it's not possible to have 4 IDE Master Drives as that is more Master Drives that any M'Board supports as they only have 2 IDE Chanel's at the most and much more importantly Optical Drives [b]Are Not Picked up in BIOS.[/b]

But turn off the ASUS Splash screen and look at what is actually being found by the Computer as it boots up. If there are 2 Optical Drives being listed there and the 2 IDE Drives by plunging the external Burner you have done something to the Software installed and damaged it to such an extent that it is no longer seeing one of the Optical Drives. If BIOS isn't seeing it the leads have either come loose or the drive has failed.

But without knowing exactly what is going on here there is no possible answer to your question as it currently stands.

Col

by haro.kms

the external drive did not mean to be permanent.. i just meant to test the hardware... in fact i have not even opened the case and touched anything inside.. all i did was plugging in a usb from the side ... i really wonder how the cables would have shifted places by any means (if they really did..)!?!?!?

about the 4 IDE.. i guess they were just somehow mapped with the name Master in bios.. perhaps they are still Master/Slave relationships... In device manager, it shows under IDE ATA/ATAPI controllers:

-INTEL ULTRA ATA STROAGE CONTROLLER
-INTEL ULTRA ATA STROAGE CONTROLLER
-PRIMARY IDE CHANNEL
-PRIMARY IDE CHANNEL
-SECONDARY IDE CHANNEL

everything is paired up... except the secondary IDE channel...

at bootup, BIOS is NOT detecting my missing F: (DVD-ROM), all that got listed is my dvd burner and the 2 HDs..

at bootup, the green light of the DVD rom does blink and with a disc inside, i can hear it spin and so on too, i can even open and close the drive freely.. that means power is going thru no problem!?

what else can i do??

by hal 9000

[i]-INTEL ULTRA ATA STROAGE CONTROLLER
-INTEL ULTRA ATA STROAGE CONTROLLER
-PRIMARY IDE CHANNEL
[b]-PRIMARY IDE CHANNEL[/b]
-SECONDARY IDE CHANNEL[/i]

The second Primary IDE Chanel shouldn't exist as this is not right. Is this being shown at the start up with the ASUS Splash Screen Turned off or in the Computer Management?

All I can really suggest at this point in time is that as you are defiantly getting power to the DVD Drive in question is to check the IDE Lead at the actual drive and make sure that it's correctly pushed in these can sometimes work loose and cause problems.

But the worry here is the second entry for the Primary IDE Chanel which should not be listed. If that line wasn't in there the listing would be correct as you have

2 X INTEL ULTRA ATA STROAGE CONTROLLER

1 X PRIMARY IDE CHANNEL

1 X SECONDARY IDE CHANNEL

So you have

1 X INTEL ULTRA ATA STROAGE CONTROLLER

for the PRIMARY IDE CHANNEL and one for the SECONDARY IDE CHANNEL

which is what should be shown By inserting the External Drive this could have been mistakenly added as another PRIMARY IDE CHANNEL which is causing the Secondary IDE channel to be partially ignored.

What if any software was installed when you plugged in the USB Lead? There could be a problem there as the OS has incorrectly identified the USB Device as a PRIMARY IDE CHANNEL which doesn't exist on the M'Board.

Col

by wrldwd2k

I have run into a similar problem and am hunting for an answer. The boot Drive is a Sata drive and the DVD-RW is IDE.
I have tried multiple jumper and cable
configurations. Chipset is an
intel D945. I have also tried long post delay.

As stubborn as this is I would think Someone has run into and solved this problem

by hal 9000

Is that right?

If so this is correct as BIOS can only show physical proprieties and an Optical Drive doesn't have any physical proprieties unless a Disc is in the drive and at this early stage the CD/DVD Drivers are not loaded.

If you have a splash screen working turn it off in BIOS and look at the devices on the system as you boot after the primary Mem Test you should get a display of fitted Optical drives and then on the next screen a list of installed components including any IDE Drives and Optical Drives but maybe no SATA Drives as the 945 Intel Chip Set M'Boards do not recognise the SATA drives by default they need a software driver installed to see these drives.

As for the DVD Drive it should be set to Master and plugged into the end of the IDE Lead with the Red Marking closest to the Power Plug on the drive. If this still isn't working correctly check the IDE Lead connection to the M'Board for the correct orientation the red strip goes to pin 1.

Col

This discussion is closed to new replies.