Question Locked

Monitor Problems, Please can anyone help?

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi there everyone, I have a problem with my computer...

I recently bought a new motherboard and installed it this morning, everything was working fine before I installed this new one...now the monitor wont come on. It definately has power to it and recognises when it is connected to the graphics card. But when I switch the power on the pc the monitor acts as if its in stand by and doesnt turn on:

Hardware:

Monitor: Samsung TFT Syncmaster 152v
Graphics: PNY Geforce 5600FX 256mb
RAM: 512 Kingston DDR400
Motherboard: ASUS A7N8X Deluxe
HDD: SATA Maxtor 160gb, Excelstor 80gb

Not sure what to do next...??? If anybody would be willing to suggest anything it would be greatly appreciated,

Thanks very much - SIMON

12 replies

by starscream

I reckon you have the wrong setting on your motherboard. I don't think it is a matter of the monitor not working, it is more of matter of the computer not working. I have had this problem before from several things, usually incorrect graphics card for motherboard. If AGP then is it the correct voltage and does the graphics card need additional power? Could be a faulty power supply, could be a jumper or bios setting that is causing is a problem.

Could be something as simple as the onboard graphics card being left enabled in the bios, try plugging the monitor into your onboard vga port and take out your geforce. If you don't have onboard graphics it could be RAM, try taking a stick out or swaping ports etc. Is there any beeping from he machine when it fires up?

by stalin_henry

Check whether u are getting a error beep when u boot the PC, or any color diff in the monitor light. Reset the RAM or try installing the VGA card in a diff slot. Did u installed the CMOS Battery? Try replacing the battery with a new one.

by starscream

Thats what I said, minus the CMOS batt but I don't think it could be that, he would be able to boot at least, just not remember settings. Also most computers have 1 AGP slot. This sounds like he can't get to the CMOS at all so it can't be a cmos problem unless he was to reset it.

Try using the CMOS jumper and short it using your manual instructions to wipe the cmos, that could iron out any cmos issues.

by dj-waddingham

Hi there,

Firstly I would like to say thanks to everybody for their reply...

Ok I have cleared the CMOS according to the user manual (ie took battery out and switched jumper for a minute) nothing appears to have changed still the same problem.

Next thing I tried was just having the CPU, Motherboard and the AGP Card all connected nothing else, still nothing.

I have also tried placing the RAM in different slots, to no avail...

The motherboard only has 1 AGP slot so couldnt try it in another slot.

I will try the card in a different PC unit but I'm sure it will work in that, so I guess its gotta be something to do with the mobo. Checked all jumpers are set to the correct standard as In manual...

Any other suggestions???

Thanks

by dj-waddingham

Hi thanks for the reply...

I am getting no beeping or noises when I start up the system, also have tried 3 different stick of RAM in different slots but still nothing. Tried replacing the battery to no avail also, not sure what else to do???

Thanks for reply

by dj-waddingham

Also there are no noises when the pc is turned on just fan etc turn on...

There are also no built-in graphics to the mobo so i guess it's not that either...

Hmm...Im confused?

by starscream

Does the monitor fully power up and stay powered up, ie green or blue light or does it power up and then go to standby (orange)?

If it powers up and goes to standby there is definitely a problem with the graphics card or configuration. If it powers up and stays powered up then it is getting a constant signal from the graphics card and could be a computer problem. You could have a dead mobo.

Check with ASUS for the compatibility of your AGP card with the mobo. Like I said before, some cards and mobos AGP slots are of an incorrect voltage. I found this out once meaning I had to buy a new graphics card when I upgraded.

by dj-waddingham

On the monitor screen it displays "Check Signal Cable", once I plug it into the AGP Card the signal disappears and then when I press the power on the pc the monitor has a green light (flickering) as if it is in stand by mode, I will have a check with ASUS about voltage settings but other than that whatever I seem to try doesnt work...

Thanks for reply

by dj-waddingham

Hi again, ok i am even more confused...

I tried my graphics card in another machine and it works, then I try the graphics card in my old motherboard and it doesn't work...I don't get it...

It works on a PC Chips board but doesnt work on the MSI or ASUS boards but I was working on my MSI board before :oS

Any ideas??

Thanks

by dj-waddingham

I have tried my graphics card in another pc and it works fine in there, the only thing is that the fan on the AGP Card doesnt spin...

So now I know it's not the Graphics Card it must be something to do with the Motherboard or connection settings on mobo...I will try fiddle about with the jumpers but i have already tried...

Also I will try another mobo see if it works in this,

Thanks for your replies, if anybody has any other ideas they would be greatly appreciated

THANKS

This discussion is closed to new replies.