Discussion Locked

Motherboard not detecting floppy disk

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a brought a brand new abit SA6 motherboard and have installed everything onto it.
My computer specs are:
PIII 733
20GB IBM Ultra ATA 100 7200RPM
Kingston 10/100 network card
Sony CD rom drive
Sony CD-RW drive
256MB pc 133 Sdram
I have no problem installing these hardware but when I bootup the computer it does not detect the floppy disk drive.

I have also changed the floppy disk drive with others to see if it works that still didn't work.
So I changed the IDE cable and that still didn't make a different either.
I have tried all the possible solution to try and solve this problem but still no solution.
I even got the latest bios update and even flushed the bios still it does not detect the floppy disk.

Can anyone help me out here????

13 replies

by dmiles

First Open the CMOS control panel and see if the floppy is listed in hard ware configuration and how the system is booting
(C,A,Harddrive).
Check the Controller Cable connection and see if the devices are listed in the Device Manager.
How dow youhave the jumpers set on the CD and CD-RW as master-slave and where on the cable do you have the floppy connected.
Try adding a connector to the to connect from the power supply and hen connector to the floppy drive.

by darky6969

Nice reply there sooulrider@msn.com but I have done all that you have mention there already and still it does not detect my floppy disk.

Thanks for your help :)

by rcliffe

The other response previous to mine covered most of the things I would try, but I was wondering why you said you changed the IDE cable. You aren't connecting the floppy to the IDE interface, are you? It should have its own 30-pin cable, separate from the 40-pin IDE cables, connected to its own connector on the board. You say the motherboard is new; if nothing solves this problem, you should be able to exchange the board where you purchased it. How did you flash the BIOS if you can't access the floppy drive??

by darky6969

I flush the bios by copying the bios flash onto a cd rom and accessing it that way.
The top answer didn't help me sorry guys I have tried that way and that didn't help either.
Thanks for trying to help...

sorry for my typo error about the IDE cable I meant the floppy drive cable

by dalbil

Open setup
and floppy disk A enabled3,5"1,44mb floppy disk B enabled.3,5"1,44mb

Because yours motherboards bios is old.
And upgrade yours bios version

by roland63

I know this is a crapshoot but are you sure you have the drive's cable connected properly? If the drive's light stays on constantly - you need to unplug that cable at the drive, flip the cable over and reinsert it.

good luck.

by darky6969

I tried that as well but 2 things happens 1. The light stays on and when I insert a disk nothing happens except the light stays on.

2. The light goes off and stays off and when I insert a disk nothing happens at all so I'm bacc to square one.So I don't really know what going on there.

Thanks for helping

by eansor

Dark-

You already have several good replys to your question, but I want to add my two cents, as I have just been through this issue on my own computer. Correct...the floppy disc drive does not belong on either IDE bus. As previously mentioned, the floppy drive needs a special cable and the cable has a twist in the middle too. Be sure to align the red stripe on pin 1 on the motherboard. Pin 1 on the back of the floppy drive is always towards the power plug side. Then be sure to check thesettings in CMOS. A:\ should be identified and in boot sequence should almost always be first. Hope this and all the others help. Good luck!

Gary

by darky6969

Thanks for a good reply eansor I have read my manual for my motherboard and what you have just mention I have read and did but still it hasn't solve my problem..

by eansor

Dark-

You already have several good replys to your question, but I want to add my two cents, as I have just been through this issue on my own computer. Correct...the floppy disc drive does not belong on either IDE bus. As previously mentioned, the floppy drive needs a special cable and the cable has a twist in the middle too. Be sure to align the red stripe on pin 1 on the motherboard. Pin 1 on the back of the floppy drive is always towards the power plug side. Then be sure to check thesettings in CMOS. A:\ should be identified and in boot sequence should almost always be first. Hope this and all the others help. Good luck!

Gary

This discussion is closed to new replies.