Discussion Locked

Mouse works w/ DOS but not Win3.1

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
486pc 33mhz 16 megs of memory dos v6.22 & win v3.1. Have tried different mouses and mouse drivers I have only com1 available and addressed it to com1. It works in DOS but when windows comesup at the beginning you can move the mouse but when windows is finished setting up it does not work. Been trying to resolve for four days. used microsoft mouse & non-microsoft. No ps/2 port available been using serial mouses. Is there something in the sys file or win ini file that I need to correct. Anysuggestions will be appreciated as soon as possible.

9 replies

by mbarker734

Sound as if you may have a IRQ conflict.

In Control Panel - Choose the Ports icon.

Com 1 & 3 usually have a IRQ of 4 and address of 03F8. While Com 2 & 4 an IRQ of 3 and address of 02F8.

If you have a modem using com3 and the mouse on com1 you could conflict as they will both try to communicate through the same IRQ. Try adjusting the setting to others that may be availible. You should be able to come up with a combination that works for you. Trail and Error, Trial by fire same difference.

Good luck,

Mark

by thejourney7

The PC doesn't have a modem or a sound card installed. But we resolved the problem. It was the resolution of the video card. Thanks For the time and input.

by dmiles

If not an IRQ conflict then you,update the driver,see if you can manually install the mouse by using add new hardware,but do the install manually,also check the BIOS control panel and see what configuration and if the mouse is enabled.

by thejourney7

The PC doesn't have a modem or a sound card. The latest driver update was done but did not resolve the problem. We have resolved it though it was the resolution of the video card. Thanks for all the input.

by rfraysier

I agree it sounds like an IRQ conflict, but your modem won't require an IRQ until you activate it, so your mouse should work, if that's the case, until you activate the modem. Windows 3.1 doesn't have the option for add new hardware, that comes in 95 & 98. I would start with your sound card, if you have one. You don't specify what additional hardware you have installed. What is on Com2? What device do you have in Windows that you don't use in DOS?

by thejourney7

The PC doesn't have a modem or a sound card. We tried reinstalling windows 3.1 and the driver plus checked the bios. The problem has been resolved it was the resolution of the video card that was giving us the problem. Thanks though for all the input.

by cpprioli

I, too, agree that it sounds like an IRQ conflict. The fact that the pointer moves OK during Windows startup, but then fails to respond upon completion tells me that there is an application being launched that is taking over the IRQ from COM1.

Aswas stated in other replies, COM1 and COM3 typically use IRQ4, while COM2 and COM4 use IRQ3. Now, if there is a modem installed and configured as COM3, this fits, as was pointed out. The reply was also correct when stating that the modem would not use the interrupt until it is activated, so... it seems as if the modem is probably being activated on startup.

There are several FAX applications that can be configured to load a "manager" applet on Windows startup, and I suspect that this is whatis happening here.

To fix it, begin by disabled the autostart feature in the FAX software. Next, if the modem is to be used, you must resolve the IRQ conflict. A likely change would be to move the modem to COM4/IRQ3, and will likely be done through jumpers or switches on the jumper. Some later quasi-PNP modems use the ICU method of card configuration, though, so be sure to identify the modem in question.

by thejourney7

The PC didn't have a video card or sound card. We tried reinstalling Windows 3.1 and also the mouse driver. Checked the bios settings. But upon reinstalling windows on a clone of the drive we noticed it wanted repeat information before going on.We resolved it by adjusting the resolution on the video card and mouse works. Thanks for your time and help!

This discussion is closed to new replies.