Discussion Locked

MS Proxy Server 2.0

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I cannot connect to the Internet using Internet Explorer 5.0 or higher using Microsoft Proxy Server 2.0 Web Proxy. I get the standard DNS error page, "the page cannot be displayed... cannot find server or DNS error". Netscape and older versions ofIE connect just fine.

Here's what happened. We were running Proxy Server 2.0 installed on an NT 4.0 SP5 server. Everything worked fine. We installed new software that required SP6 so we installed SP6. Now clients running IE 5.0 or higher cannot connect to the Internet through the Proxy server. There have been no other changes to the DNS settings or otherwise. We have been unable to find any post SP6 hot fixes that would solve our problem.

11 replies

by stillatit

On the stations that do not work, in IE, go to
tools/Internet Options/Connections/Lan Settings
Un-check the top two settings, check Use a proxy server, and make sure the numeric address of the proxy server is correct. The port number should be setto 80.

The default for IE5 and up is to automatically detect a proxy server. This apparantly does not always work.

Good luck.

by shanghai sam

Sorry, perhaps I should have specified that IE already had the correct proxy settings configured (that's one of the first things we verified). As indicated above, it was working previously going through the proxy server. When we upgraded the server to SP6, IE 5.0 and higher clients stopped working.

by curacao_dejavu

(re)install msproxy sp1;

the correct procedure to update to NT sp6 is at: MS KB Article ID: Q252517
and MS KB Article ID: Q183537

and use the proxy adress settings in IE. as it proved if netscape could connect so should IE using the correct settings.

by shanghai sam

We followed the recommended procedures found in MS KB Article ID: Q183537, and the proper proxy address settings are indeed set correctly in IE (as they are in Netscape). Netscape and older versions of IE work, but IE 5.0 and later browsers do not. We are at a loss. If it works in Netscape it should work in IE. It doesn't.

by freddo frog

First try uninstalling the MS Proxy client on one of your workstations. Reboot the system then reinstall the proxy client. Reboot again then check the proxy server settings in IE are correct, this should fix your problems hopefully.
LOL

by curlergirl

The Winsock Proxy client has nothing to do with access to the Internet through IE, if your settings are configured as you say they are. Conversely, if you have the WSP client installed already, you could try unchecking "use a proxy server" and checking "automatic configuration" instead. If this works, then the WSP client is working OK but for some reason the web client is not. In that case, I'd try installing the latest version of IE (5.5 SP1, I think), or you could try running a repair on your current IE installation. Also, is Proxy 2.0 SP1 installed? If not, you should install it. Hope this helps!

by shanghai sam

We have IE 5.5 SP1. We have Proxy 2.0 SP1. The Winsock Proxy client itself works (we have confirmed that). Whether we have "use a proxy server" checked or "automatic configuration" checked, the client still cannot get out to the Internet.

We have narrowed the problem down to Internet Information Server 4.0. On the default website, if you uncheck "allow anonymous connections" and check "use Windows NT challenge/response", that should allow us to enable "Access Control" in the Web Proxy portion of IIS. This is how it was set up before and it was working. Now we actually have to choose "allow anonymous connections" in order for clients to connect to the Internet. Note that merely checking "use Windows NT challenge/response" on the default website breaks our Internet connection. We do not even have to enable "Access Control" in Web Proxy for things to stop working. Whether Access Control is enabled or disabled, nobody can access the Internet if "use Windows challenge/response"is checked in the default web site. Problem is, we do want to control who on our network has access to the Internet. We do want users to authenticate with the servers before getting out on the Internet.

by curacao_dejavu

As I can think of nothing less, check the encription levels of the between the different IE (about internet explorer).
Dod you download the high encription or the standard encriptions of sp6a.

by shanghai sam

We only install Service Packs with the high-encryption. IE clients are running high-encryption as well. We think the problem lies with Internet Information Server itself.

This discussion is closed to new replies.