Question Locked

need help for installing xp prof in HP PAVILION DV2000

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a hp pavilion dv2000 with vista preloaded. but i want to change the os to xp prof.it is fitted with Fujitsu SATA HDD MHW2160BH.during setup xp ask for (after f6 option)sata driver.but the laptop not fitted with floppy disk drive. how can i add the driver for sata?pls hrlp me

6 replies

by thumbsup2

Just put the drivers on a CD. When XP asks for the drivers, take the XP CD out, put the driver CD in and show the installation where to look. Once the installation has read the drivers, it will ask you to put the XP install disk back in the drive.

by meridenscrafts

One of the most common problems encountered in configuring a dual-boot between Windows XP and Windows Vista happens when you try to install Windows XP on a computer with Windows Vista already installed. When you install Windows XP, it'll remove the Vista bootloader and use its own instead.

If you follow these instructions, you should be able to add Windows XP to a system that already has Windows Vista ? with minimal headache and no loss of data.
Prepping the Machine for an XP Installation

The first thing to do is to get your system ready for installing Windows XP. There are a couple of things you need to do:
Already Have Free Space?

Do you already have a free partition or a separate physical disk that you can install Windows XP to? If so, skip on to the next section.

1. Download the free GParted Live CD or use a commercial partition editor, and boot into it.
2. Use the partition manager to shrink the partition with Windows Vista to make enough room at the end of the drive for Windows XP.
3. Add a new primary partition located after the Windows Vista partition you just shrunk. Make sure it is a primary partition and formatted as NTFS.
4. Reboot

It's very important to make sure that this partition was created at the end of the drive, or else you might no longer be able to boot into Windows Vista because your partition numbers have changed.
Installing Windows XP
Warning!

If you're installing Windows XP to a separate physical drive, do not disconnect the Vista one, nor change the drive boot order in the BIOS. This will not help and will make it terribly difficult to get your dual-boot working again!

You cannot install Windows XP by running the installer from within Windows Vista, instead, you'll have to boot from the CD:

1. Make sure your BIOS is configured to boot from the CD. Some computers also let you press F12 to pick where you want to boot from ? you may use that option instead.
2. Put your Windows XP CD in the drive and press a key when you see the "Press any key to enter Windows Setup..." message.
3. If you're installing Windows XP to a SATA drive, make sure you hit F6 to load the SATA drives.
4. When you're presented with a screen that has a list of hard drives and partitions, use the arrow keys to select the empty NTFS partition you created in the previous section, then press Enter to continue.
5. Let Windows XP setup finish.

Setting up the Dual-Boot

Once Windows XP setup has finished, it'll automatically boot you into the newly installed copy of Windows XP ? note that you will not be able to boot into Vista at this point, nor will you see a boot menu option for it.

1. Once in Windows XP, download and install the Microsoft .NET 2.0 Framework.
2. Download and install the latest version of EasyBCD.
3. Once in EasyBCD, go to the "Manage Bootloader" page, and select "Reinstall the Vista Bootloader" then "Write MBR" to get the Vista bootloader back.
4. Once that's done, head on to the "Add/Remove Entries" page and select "Windows NT/2k/XP/2003" from the drop-down list, give it a name, then press "Add Entry" to finish.
5. Reboot.

Windows XP Drive Option

As of EasyBCD 1.7+, you won't be able to select the drive that your Windows XP entry points to. This is because EasyBCD will automatically search for NTLDR, the Windows XP bootloader, and pick the right drive for you. For more information, read the main Windows XP page.
Finishing Up

* If all has gone well (assuming you followed the directions here to a tee, there is no reason for it not to have), you should be presented with the Windows Vista boot menu when you restart your machine.
* You'll have the old Windows Vista entry and the new Windows XP entry you created in the steps above. Selecting each should get you into the respecting operating system without a problem.
* Feel free to run EasyBCD in either OS and customize your dual-boot by renaming entries, changing the default OS, and modifying the menu timeout.

by deepsand

If it's not on the C: drive, then it's in HP's Recovery Partition, generally drive D: or F:.

You should be able to use Device Manager/Properties to locate it, assuming that you've not already wiped Vista.

by callharry30

Me too suffering the same problem. I managed to go a few steps further by installing sata drivers using external floppy drive, but I got stuck at one place 'Matrix driver not found'. I tried loading that too, but not working

by dhawalpandya_1987

IF xp cannot find harddisk on your machine, you need to disable sata from bios.
it often termed as ahci
toggle the setting of ahci you may get the job done wityhout the sata drivers
But some bios doesn't have the option then there is no way but to find the drivers

This discussion is closed to new replies.