Discussion Locked

No CD-Rom in Device Manager

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
How do i get the CD-Rom icon to show in the Device Manager

11 replies

by dmiles

Open the CMOS control panel to see if the dual fifo controller is listed in configuration,if not enable the controller.
Check the cables to the cd-rom to make sure that are are connected properly to the hardware.
Also check the device manager to check for controller under hard disk line,you may be missing controller software,and the driver are not detected.

by curacao_dejavu

additional ; check the master and slave relationship between the hd and the cd.
usually the hd is set as master and the cd as slave..

regards,

by danpiers

If you are sure that your CD-ROM drive is working and connected to the system correctly, try this: Using the RUN command, start the REGEDIT program. Looking at the Values and Data, do a search for the word "noide" (do not use the quotes) and if you find it, delete it from the REGISTRY. Re-boot your system and the CD-ROM should be back. Good luck.

by fenaikh

Hi
1- I would check BIOS for IDE setting then
CD setting if it enable and auto detected.
2- boot see the screen for detection and notice if the CD light came on.
3- if no light then you check for hard problem.(loose connection for both data and power and the red stripe is in pin 1 for both motherboard and CD. afirm the connection on both ends.(may be need to change the cables too for both data and power ( or check the power cable and change the data cable).
4- check for master and salve setting for the CD.
6- Try CD with another PC which has a working Cd .
7- Download the manufacturer driver from there site.
8- Create a win98 boot disk and see if you can access the CD.
9- Check for broken or bent pins on both the IDE on the motherboard and HD.
10 - You may have a bad IDE change to the other IDE.

11 - Have you installed the motherboard driver from manufacturer wich came with your pc
or update it from there site. ???
12 have you check for vuiruses ....???
13 -check if it is disabled in the hardware profile.

14 I hope not --- ??// you may have a bad CD.

Good luck

Mohamed

by analyu

Molie, what happens some times is when you
install a cdrom after having windows
installed the cdrom will not show up in the
device mgr or some times win95 gets flaky.
What you do is get a win95 boot disk copy
place it in your floppy drive. Thencopy the
files oakcdrom.sys or nec_ide.sys and
mscdex.exe from the boot disk to a directory
called cdrom (that's what I like to call it)
on your C: drive . Now you are going to edit
these files on your C: drive. First edit the
config.sys and place this line
device=c:\cdrom\oakcdrom.sys or nec_ide.sys
/d:happy (this can be anything you want). Now
go to the upper left corner click on File and
do exit. It will ask you "do you want to save
this" choose yes and then exit. Now you are
going to edit the autoexec.bat place this
line c:\cdrom\mscdex /d:happy again go to the
top left click on File click on exit choose
yes to save. Now after you have exited remove
the floppy from the a: drive boot the
computer. When you boot the computer if you
want to see if the cdrom is loading just hit
the ESC key at the upper left of your
keyboard when you see the win95 logo hit it
again if it pops up again and you should see
the cdrom loading. Now when your in windows
check in the device mgr and see if the cdrom
is there. Now important once window knows
that you have a cdrom to make your system run
top notch you remark both these lines that
you wrote in the config.sys and autoexec.bat
you do not need them any more. Just editboth
files. In the config.sys place this symbol in
front of the line ; that you wrote and place
this symbol : in front of the line in the
autoexec.bat. Your done

This discussion is closed to new replies.