Question Locked

"No Signal" - Acer Aspire 360-U-D4200

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have the following configuration:

ASE360-U-D4200
Windows? XP Media Center Edition 2005, AMD Athlon? 64 X2 Dual-Core 4200+ (512KB + 512KB L2 cache, 2.2GHz), 2GB (1G/1G) DDR SDRAM, 300GB SATA hard drive, DVD-Dual drive (DVD+/-RW), DVD-ROM drive, 9-in-1 card reader, ATI? Radeon? X1300LE graphics, TV tuner with PVR (personal video recorder) and remote, gigabit LAN, V.92 modem

Monitor Details:

Acer AL1916W

Product Features

19" WXGA 1440 x 900 (Wide Screen)
High Contrast Ratio: 700:1
Brightness: 300 cd/m2
Fast response time: 5 ms

Specifications

Model AL1916Wcs
Display Size 19" diagonal (Wide Screen)
Display Type TFT active - matrix
Pixel Pitch 0.284 mm
Maximum Resolution 1440 x 900
Contrast Ratio 700:1
Brightness 300 cd/m2
Input Signal Analog VGA
Response Time 5 ms
Viewing Angle 150o Horizontal / 130o Vertical
Power Consumption 36 W
Power Adapter Internal
Kensington Lock Supported
Weight 4.1 kg
Dimensions 448(W) x 369(H) x 182(D) mm
Warranty 3 years limited *

Problem: About 2 days ago, I was playing Call of Duty 2. I finished the game, and was viewing the credits, when all of a sudden, my monitor went blank. I thought, the game was stuck or something, so I tried to press "ALT + TAB" and "CTRL +ALT + DEL" to get back to windows XP. Then I thought the OS was stuck, and I reboot the system. On rebooting, I got the "No Signal" message on the monitor. I tried rebooting several times, and the result was the same.

I opened up the CPU unit (power turned off), pressed on the video card to ascertain that it was tight in the slot, but the effort was in vain.

Does anyone know or can suggest how I could debug the problem...? I am using the LCD monitor through the analog output from the CPU unit. I am planning to test the monitor on a friend's PC today, in an effort to narrow down the problem.

But in any case, has anyone experienced a similar problem, and if yes, how would I narrow down the problem to identifying what component is causing this problem, due to a loose conncetion or a failure.

Your help and advice would be appreciated.

Thank you.

Regards,

Smartlook77

12 replies

by hal 9000

If it doesn't work change the Video Lead and try again. If you still get nothing replace the Monitor.

If the monitor actually works unscrew the holding screw on the video card and pull out the card and check the fan on the card to see if you can turn it. If you can not spin the fan freely replace the Video Card as it's most likely fried and died.

You can also try turning off for a few hours and then try turning back on and see if you get a display if you do you have a heat sensitive problem where when something is reaching a certain temp it fails. The obvious things are the Monitor, The Video Card or the M'Board look for anything with a Fan on it except the CPU and make sure that they are actually running. Also make sure that the CPU fan is both working and that there is not a build up of dirt and other rubbish in the Heat Sink. If there is remove the fan and clean the Heat Sink without removing it from the M'Board.

A couple of other things to look at the LED on the monitor does it change colour when you turn on the Computer? Try turning on the monitor and look at the LED and wait till it goes into stand by mode or better still disconnect the Video Lead and see if you get a warning message that there is no Signal Present. If you get a picture on the monitor telling you that there is no Video Signal the Monitor is at least working when it's cold. Replace the lead and then turn on the computer and see if you now get any form of picture. At the same time look at any front panel LED's and see if they light up.

If you didn't see anything with the Video Lead disconnected it's likely to be the monitor and if you don't see anything with the Video Lead connected and you did with it disconnected it's most likely to be the Video Card.

If it works and stops when it gets hot you most likely have a failed fan which is allowing something to overheat and stop the system .

Lets know how you get on.

Col

by smartlook77

Hi,

I tested the monitor on a friend's PC, and it works fine, so the monitor not functioning is ruled out. I also tested my hard drive on his PC, and that worked out perfect too.

As far as the dust on the CPU fan and heat sink are concerned, I have checked both, and there is not much dirt present, as the PC is fairly new and because it is always away from dusty environments.

The fan on the Video card works as well. Although I did not remove the video card from the slot, I can clearly see the fan on it spinning.

Now, what do I do next to narrow down the problem, and find the culprit.

Thank you.

Regards,

Smartlook77

by hal 9000

Absolutely no picture on the screen even at the POST Level. Change the Video Card. If that doesn't cure the problem your next choice is to remove everything except the RAM CPU and Video Card and try again. If still no joy replace the M'Board and try again.

As this is still a new system is it covered by a Manufactures Grantee? If so why not send it back to it's maker to fix the problem?

Col

by shawn_soc

Hi me too getting the same problem also. totally the same aftre 5 to 6 hour power up can use again but aftre few hour same black do have any tip on this

by george

I too just started getting the "No Signal" error display from the monitor. The monitor is new, purchased within the past 3 months.

What is strange is that I am typing right now with the No Signal error msg being displayed. After a few minutes the screen goes black and the No Signal msg goes away.

So I assume that the ATI card that I purchased is bad (not enough power), or monitor is bad. Overheating of the Sony VAIO may be an issue as I have one of the liquid cooled units.

Once I figure out what is broken I'll post my results.

by janronel

mine too, i have x1300 and when i play all kinds of games except Company of Heroes, all my games say no signal.. i really like the one "Mount and Blade" And after about 15 minutes it also says no signal

by spencersimon

My monitor just started doing the same thing randomly. I was just wondering if you were able to find a fix for it. I called acer and they said it would be in the shop for 2 weeks plus shipping time. I cant go without it for two weeks.
thanks
Jason

by haasjoel

it is not a Windows problem. I run it with Mac OSX on a new MacBook and have same problem.

by gokuuson

Don't know if this will help you, since you have a different model from my 24", but perusing other forums, I found that turning off your monitor, pulling the plug out of the socket and then plugging it back in has solved the issue for me.

It suspiciously seems to do something with the Windows Update that just currently got installed, so you could try my strategy, or if you have, then I'm not sure what the problem is.

by redmann415

first to be sure we were haveing the same prob. i would get this annoying box in the middle of my screen reading "no signal" a min or two later the screen would go black then come back like it never happened. if this is the same prob that you were having try this. turn your monitor off, then remove the avi cord, turn the monitor on leave it bee with the acer screen for about 30 secs. then turn the monitor off again and unplug it. wait about a min then plug the avi cord back in then the power, next turn on your monitor and poof it is like you never had a prob. it worked for me and i need to do it every once in a while. a little annoying but i only paid 200 for this mon brand new from a store that was going under i cant return it and when it works it is great. hopefully it works for you. good luck

by miamishores

I have 2 monitors connected at the same time on my tower. I have been working with both as one large screen for a few months, and the no signal square comes up all the time.

Flavio

This discussion is closed to new replies.