Discussion Locked

NT is not detecting 40GB Hard dist

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

we tried to install windows nt server 4.0 as a member server in 40GB hdd. We booted through cd at the time of creating partion it detects only 8GB. First we made 4GB initial partion for OS. Then we made 35GB extended partion using windows 98 startupdisk. Later we tried to partion the 35GB into two partion using disk administrator in NT. But it is detecting only 17 GB. Remaining 17 GB(approximately) where it is going we don't know.

We tried to partion the Disk using Windows NT cd also. But we are unable to utilise the entire hdd.

Please give solution to us...!

Sakthi
bubloo@hotvoice.com

13 replies

by jlouis45

this is a typical problem of higher capacity HDD. You make 3 partions of 15 / 15 and 10. coz win98/2000/NT doesnot handle this higher capacity HD Drives. After this you boot with the CD and install the NT / Workstation the problem if it still persists check the HD manufacturer's site for bios updates and also drives for the same. After partitioning make the active partion.
All the best

by bhrdwh

Sakthi,
Are you using IDE or SCSI Systems ?? I take it that its a IDE & you are probably using a PC to istall NT & its BIOS does not support more than 8 GB.
Check one thing, does the system show entire 40GB as HDD capasity in bios ? Suggest you updraed the bios with latest patch.
Also once its installed, go to Disk Admin & see the HDD info. I am sure it will be there as free disk space. You can then create partitions & use the whole 40GB disk.
Akash

by ronnonf

The vanilla copy of Windows NT 4 was not able to see more than 4 or 8Gb. If you would install Sp3 (or greater) you should have no prob. What you can try to do is burn a CD containing all the updated files. Then use that CD to install NT.
I had a similar problem, I installed NT then the service packs and used PQMagic to resize my drive. Some of my system drives are set to 16Gb.
Another idea is to install Win2k native will allow you to address all the space. Good luck.

by @lberto

That's just a bug of Windows NT 4.0, just install your Windows NT on your 2.0 Gbytes partition (remember that it needs a FAT16 partition to install, latter if you want you can make it NTFS), once you are done with this installation, install the latest Service Pack available (For Windows NT 4.0 SP6a, for Windows NT 4.0 Terminal Server SP6), you can download them from support.microsoft.com., also remember to download and install the post patches.
After installing this go to Disk Administrator and build the other partition, some times it won't detetec the whole total at the first time, just reboot, start it up again and for sure it will work.
It happens to me, I have a 4 Processor P-III 500 DG with 4 Gbytes RAM and 2 Raid of 40 Gbytes, and that's the way I could install it.
For sure it will work, good luck,

@lberto

by kthurston

If the drive is IDE:
1) Ensure the BIOS can handle that drive size
2) Hook the drive to an NT workstation as the SECONDARY MASTER. Boot to NT and creat your 40GB NTFS partition and format it.
3) Hook the drive back to your new server and boot to cd and perform your install. (During the install don't worry about drive size mis-reporting. It's a legacy IRQ problem that will correct itself after installation is complete and SP3 or higher is installed).

If the drive is scsi, hook up an IDE drive with NT already on it to the server and boot to that, install the scsi drivers, then use disk manager to complete the same process for the IDE drive.

I know this works. I just did it two weeks ago.

Much luck to you!

This discussion is closed to new replies.