Discussion Locked

PC is dead

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a computer that I put together about
6 months ago, an AMD processor, new motherboard,
new case, new video card, new hard drive, new
R/W CD-Rom, new memeory (RAM), new power supply.

I had my old cd rom connected to my new R/W cd rom.
Idecided to disconnect the old one and just use the
recordable cd rom. I disconnected it from the IDE
cable both cd rom's were sharing. I then set the
the R/W cd rom to master. When I turned it back on
the computer would run for maybe 3-5 seconds and
then the power would go off. I have removed every card one by one and then tried to turn on the computer hoping to find the culprit but no luck
so far. I have also tried reseating the memory
and have had no luck! If any one has any
suggestions I would appreciate any help anyone
could give me.

Thanks in advance,

Mark Ritter

20 replies

by dmiles

One common error when disconnecting cables is that you may have a loose cable connector on the motherboard,check all connectors

Check the power connectors to peripherals and make sure they are connected properly

Check the power cords and also check the switch to the power supply to make sure that it is not switched off

by mbr2

Thanks for the suggestion but everythiing seems to be
connected o.k.

by drdmc

1. Make sure that your power outlet is good. (Plug a lamp into it to verify).
2. Check the line voltage switch on the power supply. It should be set to 110v.
3. Use a multimeter to check the continuity of the wires going from the power supply or motherboard to the power switch. Be sure the power supply is unplugged from its AC power source.
4. Remove the power connectors from everything except the motherboard and retest. Then begin replacing the power connectors on the internal devices until the boot fails and you should find the problem device.
5.If the device listed in the BIOS as a boot device has a bad connection or cable, it can cause the system to halt with no messages or beep codes.
6. Make sure that the processor fan runs. AMD processors get hot fast.
7. Good luck.

by thechas

If you set the drive parameters for the CD drives in BIOS settings, the motherboard may be confused by the drive change.

First try setting the CD-RW drive back to slave. If the system now boots, go into BIOS settings, and set both drives on the channel to auto detect.

If it doesn't boot, try placeing the old CD drive back into the system. Again, if it boots, go in and change the drive settings to auto.

Alternately, go through the CMOS memory / BIOS reset procedure for your motherboard.

One other off the wall idea is that you have a power supply that needs a heavier than normal load to stay on. This can be checked by simply connecting the power cable to an additional drive.
If the system now boots, you need to replace the power supply.

by mike (from canada)

You might have the voltage setting on the power component in the computer set incorrectly, OR your connection is loose, OR your wires INSIDE the cord are loose which means BUY A NEW CORD, OR you are plugging the main unit into a temporary power supply and all the power is deleted, OR you have an animal or a kid that accidently plays with the cord in such a way that the connection is broken.

by jimj777

NUMEBER 1) WHAT KIND OF CPU YOU HAVE? IF YOUR RUNNING AN AMD ATHLON 1 GIG. YOUR POWER SUPPLY SHOULD BE AT LEAST 300W INSTEAD OF THE 250W.
NUMBER 2)YOU DISCONNECTED THE IDE CABLE BUT HOW ABOUT THE POWER MOLEX CONNECTOR. YOUR OLD CDROM COULD BE STILLDRAWING CURRENT.
FOR EVERY TWO HARDWARE COMPONENTS(EX.-CDROM,HARD DRIVE,CD-RW,FLOPPY...)YOU ADD ANOTHER 50W TO YOUR POWER SUPPLY. TRY A 400W IT SHOULD WORK!

by mbr2

Jim,
Thanks for the advice! It seems to have been the power supply.
I will probably go to a 400W power supply per your
suggestion.

by jesselou

your power supply maybe defective why not try a new one matching the power supply of your mobo.or recheck your power supply connections to your mobo maybe it is only loose. if no progress at all then replacing your power supply with a new one is theother alternative.

by maddiuex

Is the Cdrom cable ( Ribbon ) on correct, This could cause your system to do this.. Make sure the red or blue line on the ribbon is on the number 1 pin on the system board, and cdrom.

Hope this helps?

by derekdcosta

Having tried everything else maybe check the power on switch itself.... or it's connection to the motherboard. Something could be causing it to activate... especially true if your BIOS is set to soft power down (press switch for 4 seconds) ?

Derek

This discussion is closed to new replies.