Discussion Locked

PC needs two boots to get running

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I recently upgraded my PC from a Pentium 3 500Mhz to a 1000Mhz Athlon which obiously required changing the motherboard. I reinstalled Windows ME as i was advised to do. After ironing out many of the problems the computer finally booted properly. Now however if i try and restart my computer it goes through the whole process and as its about to load up the windows taskbar the harddisk stops and the computer resets itself. The computer will now load up But only afer it has ran scandisk becauseit detected an improper shutdown. at first there were some compatability problems with my drives but i don't think its that, i have a internal 250Mb Zip Drive on the Primary IDE as the slave. i also have a standard 48x CD drive as the secondry master IDE and a RICOH DVD Drive with a CDRW built in as the slave. There is a 25Gb IBM hard disk as the Pri master. I have tried reinstalling Windows again but to no avail. Please help me!!

13 replies

by natas

The AMD Athlon requires a special power supply, if you are using the case that you used for the pentium 3 it might not be able to support an Athlon. I'm check with the place where you bought the case and see wether or not it is able to handle an Athlon. This sounds strange, but it is true I am an Athlon user myself I know.

by nettek

I agree with the first answer. It sounds like a power problem. However, since the connections off your power supply fit your motherboard, I would check the motherboard documentation. The board may have built in transformers that can supply the correct voltage to your processor. Perhaps there is a dip switch or jumper you can change that will correct the voltage problem.

by mphoffar

I would agree with the power problem. However, this sounds similar to an IRQ or DMA conflict somewhere. I realize that ME came with pretty much the newest everything, but I'd look into getting the latest bus mestering drivers from the chipset manufacturer. Some of these had a AGP miniport driver that solved a lot of headaches like this also, so that might not be a bad idea to load that if there is one available.

Good Luck to you

Mark

by ugotdave

So many opinions! Well here is mine. When I have trouble booting into an O/S I like using the MSCONFIG Utility. If you never used it just type in msconfig at Run and press Enter. On the General Tab you will see the Selective Start Up option, choose it and then take away the check mark from the Load start up group items. Reboot and see what happens. If it boots normal add back groups one at a time to see who the culprit was. You should keep StateMgr, Systray, ScanReg in the groups that load, but remove them at first to see if they are the problem, then make them the first ones you put back.

David?

by smltec

indeed go to msconfig. click on the advanced button at the bottom of screen and put a check in enable startup menu.ok>ok>and restart. At the menu screen choose step by step and watch what is loading when the computer hangs. This is the culprit and is probably a vxd driver that shouldnt be loading. Also if you arent going to use the computer in a network, go to static.vxd tab in msconfig and uncheck ndis.vxd. this is a nic card driver that had been known to affect startup and shutdowns. Lastly, go into bios and disable power management.

hope this helps

by lumumba

First of all go to Cmos then see in your documentation about booting from OS/2 disable that option and then change booting system make C: is first then a: and then restart your sytem after saving changes if this option are not help you goto next...Go to Cmos again and all pages and lines return to default option and save it. Restart again your system if this option can not help you please Fdisk your Hard disk then format it and make it bootable (sys a: c:) before install again Windows restartyour Machine to see can be boot or not i hope to be OK in this option then Setup Windows 98 before upgrading to you're favourite Windows ME. Please note if Windows 98 is running properly you'll go ahead for your installation (you're 'ME') and if theproblem appears again you're software are not OK.
I wish you the best.

This discussion is closed to new replies.