20 replies
by shaggysmine Accepted solution
by thechas Accepted solution
Check Device Manager and see if you have any devices with a yellow "?" or "!".
If so, you may need to reinstall device drivers, or a fresh reboot may fix it.
An easy way to force a drive update is to uninstall the device and then reboot so that Windows can find new hardware and install the driver again.
Have you tried a different set of speakers? Could be as simple as a power supply failure from the power surge.
You say can't find the modem? Do you connect directly to a cable / DSL modem, or do you connect through a router?
If a wired connection, it is not impossible that the port is damaged.
For a wireless connection, it is not impossible that the RF transmitter has failed.
Open network connections, and check the connection status. If you have no connection, check for any indicator lights an the Ethernet Jack, or the Wireless status light on the computer.
Post back with the make and model of your computer and any peripherals that are connected for the Internet connection.
One last thought, if you have an outlet strip that only some of your equipment is plugged into, make sure that the breaker on the outlet strip did not trip.
Chas
by shaggysmine Accepted solution
Okay, there are no yellow ? or ! in Device Manager and all says it is working and has the correct drivers.
The speakers work fine on the other PC I have on the same network as so does the ethernet and port on a router.
All the lights are on and the power strip has everything working. The Message for Audio Service Not Running says This computer cannot play audio because the Windows Audio Service is not enabled. Would you like to enable Windows Audio Service? When I click to yes and got to the Sound window it says Realtek Digital Output and Speakers are enabled/ There is a check on the speakers, but not on the Realtek icon.
The computer is an HP Pavilion a6110n PC. There os the monitor, wireless keybord and mouse, speakers and external harddrive that was not hooked up at the time it shut down.
Hope that answers your questions. I appreciate your time.
by thechas Accepted solution
Okay.
I have seen some weird problems when a Microsoft driver update is installed.
Open device manager and check that you have the correct driver versions as per the HP driver list for your computer.
You usually need to click on the driver details button to get the driver version.
Driver - Audio(?1)
Realtek High Definition Audio Driver Update
2008-03-01 , Version:6.0.1.5548, 12.34M
NVIDIA LAN Driver
2007-06-20 , Version:65.7.4.0, 1.08M
Summer 2007 original drivers for the NVIDIA LAN solutions.
If you have different driver versions, download the drivers from the HP website and transfer them to the computer.
Uninstall the device from device manager.
Then install the HP driver.
Chas
by shaggysmine Accepted solution
by thechas Accepted solution
Those are the correct two devices.
You can choose the option to uninstall the driver files as you have a new driver ready to install.
You might double check that the speakers are plugged into the correct jack, the green out jack.
Also, these are powered speakers. Most output jacks on computers can barely drive headphones and will not drive unpowered speakers.
For the network port, double check that the connection lights at the jack the cable plugs into turn on.
The more I think about this, the more I suspect that you had two hardware failures at the same time. Both the final output stage of the speaker out, and the Ethernet output.
Is it possible that the cables for both were pushed hard into the computer and damaged both jacks.
Still, it will not hurt to do a driver refresh.
But, if reinstalling the drivers does not fix the problem, there is a high possibility of a hardware problem.
Chas
by shaggysmine Accepted solution
by bapster Accepted solution
by shaggysmine Accepted solution
by bapster Accepted solution
Make sure you right click and run command or cmd
As Administrator and then try the sfc /scannow
by shaggysmine Accepted solution
by gharlow1 Accepted solution
by shaggysmine Accepted solution
by thechas Accepted solution
Just had a new thought on this.
If the PC was off, but plugged in, a weak CMOS battery could cause the BIOS settings to change.
Boot up the computer and enter BIOS setup.
Look for the integrated peripherals, and set the Sound and Network adapters to disable.
Save and Exit Setup.
Enter BIOS setup again, and enable the devices.
In the PC Health section, you may be able to see the CMOS battery status or voltage. Any reading less than 3.0 volts indicates that the battery needs to be replaced.
Chas
by shaggysmine Accepted solution
by thechas Accepted solution
Thinking about this, if the PC was off when the power went out, a weak CMOS battery is the most likely problem.
These are typically CR2032 coin cells and are nominally 3.0 volts. A good battery should measure 3.1 to 3.3 volts. Anything less than 3 means it needs to be replaced.
If you replace the battery, you will need to enter CMOS setup and check the settings. You should be fine choosing the recommended or default settings.
Chas
by shaggysmine Accepted solution
by atlantaterry Accepted solution
As a support tech, several times end users had no speaker output and for some reason their system's audio had been set to "Mute". As soon as I unclicked "Mute" everything returned to normal. Your problem could be as simple as that.
Reboot. Hold down the F8 key. Select "Safe Mode". Sometimes things get fixed automagically by running Safe Mode. It is worth a try.
Terry Thomas
President
PC Tech Support
Atlanta, Georgia USA
by itkimk Accepted solution
I have a client with a Toshiba Laptop running Vista who would lose her Internet connection periodically. Usually I would remove the device and re-install the driver. After a power outage, no matter what I did I could not get the network adapter or the wireless adapter to work( I even tried a USB wireless adapter). I backed up her profile and did a factory restore and everything worked fine. I have seen this on a couple of Vista machines. Sometimes, with Vista, it is best to cut your losses and just back up and re-install.
Time trying to get networking functioning again: 3-4 hours.
Time to Back up and re-install : 1 hour 45 min.
by shaggysmine Accepted solution
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending