Discussion Locked

Printing Issue with wk2 Server & HP 5500dn

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I'm experiecing a problem with a network printer (hp 5500dn). Its setup properly and users can print to it through the server share. The issue is this: after a user prints a job, the server queue retains a copy of the print job. It accumulates (today was up to 80) and when the server is rebooted the printer proceeds to spew these jobs wasting a lot of paper and toner. This occurs even with a test page. I've gone over the HP settings and the options for this type of printing are disabled. My immediate thought is that this is either a Spooler issue or an issue between w2k and the Jetdirect in the priter itself. Any help would be appreciated.

11 replies

by jireland607

When data is sent to the printer, headers and footers are fixed to the top and bottom of the document to pass over commands. My guess is that a command is missing which says that the job has been transferred to the printer.

This will be written by the printer driver so make sure you have the correct driver type and latest version.
If you go to the hp website at:

http://h20000.www2.hp.com/bizsupport/TechSupport/Resource.jsp?locale=en_US&taskId=110&prodSeriesId=83875&prodTypeId=18972

...they have an automatic driver checker. Give that a go.

James

by acgphx

When the printer was setup last week the most current drivers (found on that exact page) was used. It may be the case still but I'm doubtful this ia a drivers issue (though I'll reload for good measure). I'm going to try a few users attached directly to the printer without the server queue and see what happens. I'll post the results later today or tomorrow.

by acgphx

Its not a JetMobile (wish it were that easy to fix). Prior to this issue the printer was working fine. I just got back from the site where I refreshed the server's drivers (just in case) and created the server on a few workstations (without the link to the server). So far the server based printer is doing the same thing whereas the direct link via a workstaiton isn't showing this problem. Damn annoying. I'd prefer not having to manually setup this printer accross 35 users in 2 WAN sites.

by mikex

If your printer has a IP address =>

Unshare the printer from the server (for all 2k and XP users - leave it only for 98 users) and add a local printer on every user with a IP network Port - this will unload your server and you'll avoid future troubles

by acgphx

Thats exactly what I've had to do. Previously this was all shared through the server. The solution I'm seeking is one which will allow central management again, but thanks.

by curlergirl

A couple of thoughts - Are you running real-time antivirus scanning software on the printer server? If so, make sure that the spool folder (if it is in the default location, that's \%systemroot%\system32\spool\printers) is EXCLUDED from real-time scanning. Also, could the NTFS permissions on the spool folder somehow have gotten changed or corrupted? Check and make sure the permissions are set to: Creater/Owner, Administrators and System - Full Control.

Are you getting any error messages like "Access Denied"? This can happen if the permissions are wrong; it can also happen in Windows 2000 if you are running SP2 or earlier and are logged on to the print server computer with a logon that does not have administrative-level rights to that computer. If that's the problem, upgrade to SP4 for Windows 2000 (you should do this anyway if you haven't already).

Hope this helps!

by acgphx

The issue turned out to be something more with sharing it via the server. Once I removed the queue fromt eh server and allowed the HP to handle its own queue independantly everything straightened out. Each workstation now has a 1-1 relationshiop with that printer. My apologies for taking so long to close this.

by voldar

I am sure you checked the Printer - Properties - Advanced options, and uncheck the "keep printed documents".
And yes, if you want, change the SPOOL directory path to another location (on another drive), to have more space in your c:\ (because if you want to have the documments kept in the "spooler", well, your HDD partition will be soon full of "unwanted" documments, and you'll experience performance losts).

by csisamba

This problem can be a hassle. I hope you have this solved since you posted months ago. Please try these steps if you have not.

1. verify that the "enable bidirectional support" option is not checked under the ports tab of the printer properties.

2. verify that any antivirus programs exclude the print servers queue folder.

Good Luck

This discussion is closed to new replies.